Not Able ping Management port for 5520

[syed baseeruddin]

Hi

in core switch in create vlan 94 int vllan 94 192.168.50.254

and assign wlc management port 192.168.50.252

i make untagged vlan 94 at time WLC installation

with service port i can access WLC GUI

with Management port i am not able to login with out switch also when i directly connect to lan Port also

[Sandeep Choudhary · Accepted solution]

paste the swicthport config where WLC is connected!!!

Did you configured native vlan on switchport ?

[Sathiyanarayanan Ravindran]

Configure Native VLAN 94 on the switch port. At-least on one end, you have to tag VLAN.

Its recommended to tag the VLAN on WLC end.

[Dustin Anderson · Accepted solution]

I had this same issue, best is the remove the native vlan on the trunk and have the wlc tag the vlan. This is what I have been doing with the controllers without issue.

[syed baseeruddin]

Thanks

management 1 94 192.168.50.252 Static Yes N/A
redundancy-management 1 94 0.0.0.0 Static No N/A

these port are already tagged then telling again tagged via cli

please tell how can do this

[Haydn Andrews]

please post:

Switch port/s config 

From WLC

show interface summary

show interface detail management

show port summary

[syed baseeruddin]

Thanks support Team ,

Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
management 1 94 192.168.50.252 Static Yes N/A
redundancy-management 1 94 0.0.0.0 Static No N/A
redundancy-port - untagged 0.0.0.0 Static No N/A
service-port N/A N/A 0.0.0.0 DHCP No N/A
virtual N/A N/A 1.1.1.1 Static No N/A

after that i assign ip  to service Port  i am able to access wlc via gui

but for Mgmt LAN 1 is not wking with and without switch

for core switch

int gi1/1

switchport mode trunk

switchport trunk allowed vlan all

and one end of the cable is is connected to lan port of ucs wlc

At that installation time of wlc

0: untagged : 94

[Sathiyanarayanan Ravindran]

Tag the VLAN 94 on the WLC management interface. The issue will get resolved.

[syed baseeruddin]

Thanks,

i will do again from scratch again

can i make  command line to make tagged for mgmt interface in wlc

if am doing from scratch at time installation 0:untagged =vlan number or 0

then switch side 

vlan 94

int vl 94

ip add

int g1/1

switch port mode trunk

switchport trunk native vlan 94

please correct if any thing is missing

i also do not configure CIMIC in UCS Server 

i need CIMIC ip add i should use different subnet 

it is optional or mandatary to configure in cimic ip add for 5520 wlc

please advice

sw

[Sathiyanarayanan Ravindran · Accepted solution]

Either one end you have to Tag the VLAN. Do only on the WLC via taking the console of it.

If you do on the WLC End, switch end its not required. 

Its good to enable the CIMC of the WLC, So that you can take the console of the WLC in case of any issue 5520 WLC CIMC Configuration

[syed baseeruddin]

Thanks,

in WLC 0:untagged 0

this command in need apply 

or any other command

[syed baseeruddin]

Thanks,

How can i do tagged for managment vlan

at time begining i make tagged for example 0:untagged=94

it already tagged managment vlan 94 

please correct me i am wrong

[syed baseeruddin]

Thanks

management 1 94 192.168.50.252 Static Yes N/A
redundancy-management 1 94 0.0.0.0 Static No N/A

these port are already tagged then telling again tagged via cli

please tell how can do this 

[Sathiyanarayanan Ravindran]

Still you are not able to access it ?

Can you paste the current switch configuration?

[syed baseeruddin]

Hi

Thanks

these setting applied previously also  tommorow i am going site need to make wlc gui 

please advice

There are two controller and core switch

in core i will create vlan 94

int vl94

ip addd

 and int g1/1

switchport mode trunk

in the wlc

Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
management 1 94 192.168.50.252 Static Yes N/A
redundancy-management 1 94 0.0.0.0 Static No N/A

i had made at installation 0:untagged=94

i assume that my management vlan is tagged

i am confusion these tagging of management vlan 

experts please advice 

as i am not able to ping the controller 

[syed baseeruddin]

There are two controller and core switch

in core i will create vlan 94

int vl94

ip addd

 and int g1/1

switchport mode trunk

in the wlc

Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
management 1 94 192.168.50.252 Static Yes N/A
redundancy-management 1 94 0.0.0.0 Static No N/A

i had made at installation 0:untagged=94

i assume that my management vlan is tagged

i am confusion these tagging of management vlan 

experts please advice 

as i am not able to ping the controller