Reset to factory default doesn't work on 1552i AP

load.cabral · ‎09-17-2015

Hello guys,

I need help with AP 1552I, How do I reset the entire configuration?

Print:

ap: ?
? -- Present list of available commands
arp -- Show arp table or arp-resolve an address
avr_echo -- AVR echo test
avr_version -- AVR show version
boot -- Load and boot an executable image
cat -- Concatenate (type) file(s)
clear_ether -- clear ethernet port statistics
copy -- Copy a file
delete -- Delete file(s)
dir -- List files in directories
dump_regs -- dump reset registers
etest -- test emac driver code
ether_init -- initialize ethernet port
flash_init -- Initialize flash filesystem(s)
format -- Format a filesystem
fsck -- Check filesystem consistency
help -- Present list of available commands
init_pci -- initialize pci bridge
led_test -- cycle led patterns
load_helper -- Load and initialize a helper image
memory -- Present memory heap utilization information
mkdir -- Create dir(s)
more -- Concatenate (display) file(s)
rename -- Rename a file
reset -- Reset the system
rmdir -- Delete empty dir(s)
set -- Set or display environment variables
set_baud -- set baud rates
set_sleep -- Pause (sleep) for a specified number of seconds
show_ether -- show ethernet port statistics
show_mem -- show memory
show_pci -- show pci setting
show_power -- show AVR power source
show_reset -- show reset status
switch status -- report push button switch status
tar -- extract or listing a tar file
test_ddr -- test ddr
test_ddr_rd -- test ddr_rd
test_ddr_wr -- test ddr_wr
tftp_init -- Initialize tftp file system
type -- Concatenate (type) file(s)
unset -- Unset one or more environment variables
version -- Display boot loader version

ap:

Tks,

PETER MOOREY · ‎09-17-2015

Your AP is currently in ROMMON (mini boot loader), usually this is because:

- The boot up process was interrupted

- The software image was deleted and there is no valid software to boot

- The configuration-register is misconfigured

Anyway, to factory reset the configuration:

http://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/7-3/design/guide/Mesh/Mesh_chapter_01.html#ID1177

To recover the software (in case it was accidentally deleted):

https://supportforums.cisco.com/document/56156/access-point-rommon-recovery-ap-prompt-recovery-example

Hope this helps,

Pete.

load.cabral · ‎09-17-2015

Hey Tks,

This process I had executed
The password for the User is not working, I need to reset and start again

Log

User Access Verification

Username: cisco
Password:

% Authentication failed

Tks,

load.cabral · ‎09-17-2015

permission denied Rename, I can not change the file name

procedure: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/15_2_4_JB/configuration/guide/scg15-2-4-Book/scg15-2-4-chap22-trouble.html#pgfId-1036746

1 - Resetting to the Default Configuration

1.1 Using the CLI

ap: dir flash:/
Directory of flash://

2 -rwx 265 <date> lwapp_mobileconcierge.cfg
4 -rwx 64 <date> sensord_CSPRNG0
29 drwx 1152 <date> c1520-k9w8-mx.ap_kmr1_esc.201301251143
26 -rwx 64 <date> sensord_CSPRNG1
6 -rwx 241 <date> env_vars
28 drwx 0 <date> configs
5 -rwx 7192 <date> private-multiple-fs
30 -rwx 97898 <date> event.log
7 -rwx 36 <date> mesh_port_cfg.txt

25010688 bytes available (6858240 bytes used)

ap: renam

ap: rename
usage: rename <old_name> <new_name>

ap: rename mesh_port_cfg.txt mesh_port_cfg.old
rename: no such file or directory

ap: rename mesh_port_cfg.txt
usage: rename <old_name> <new_name>

ap: rename mesh_port_cfg.txt teste.old
rename: no such file or directory

ap: rename <mesh_port_cfg.txt> <teste.old>
rename: no such file or directory

ap: del flash: mesh_port_cfg.txt
Are you sure you want to delete "flash:" (y/n)?y
File "flash:" not deleted -- no such file or directory
Are you sure you want to delete "mesh_port_cfg.txt" (y/n)?y
File "mesh_port_cfg.txt" not deleted -- permission denied

ap:

PETER MOOREY · ‎09-18-2015

The username and password are Cisco not cisco. Make your you enter it with a capital C.

load.cabral · ‎09-18-2015

I auditioned, did not work