TFTP IOS Upgrade -> Permission denied - Cisco AP
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-10-2021 05:26 AM - edited 07-05-2021 01:17 PM
Hello guys,
im trying to giving a AP a Lightweight or Autonomous Image (both not working). The AP has no image rn and it is blank. It is a AIR-LAP1142N-E-K9
(It had both images kw7 and kw8 but when i deleted it and tryed to do it myself then it didnt work)
-When I try to xtract the .tar data then:
These are the commands that Im giving the AP:
-I can also ping the AP with my Laptop (My laptop IP: 10.200.15.97)
-I dont have a default router but i think i also dont need one (WLC is PoE and the AP is connected with it)
-btw tftp_init is not working (someone told me i also dont need it)
This is my tftp Sever:
My windows setting:
My laptop IP:
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-10-2021 05:29 AM
I researched so long but couldnt find a solution. I rlly hope someone can give me a helpful advise
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-10-2021 07:23 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-10-2021 10:55 AM
Have you tried to upload the image using the mode button? Try a different tftp server also... I run multiple just in case one gives me issues.
*** Please rate helpful posts ***
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-10-2021 11:40 AM
Did you follow the below URLs for Step by Step procedure
Make sure your windows firewall is turned off along with any other enterprise antivirus/security/firewall applications you are running.
Can you send output of the following commands:
dir flash:
Thanks,
CJ
""Please rate all helpful responses""
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2021 04:48 PM - edited 05-11-2021 04:51 PM
Useful tips above from the others.
In the screenshot you provided above for the tar command you've typed the wrong IP address (.95 instead of .97)- so you're telling the AP to TFTP from itself so no surprise it got permission denied!
More generally that would happen when a file is not WORLD readable on unix/linux, on Windows it depends on the server you use, best to make sure the file and folder permissions are set to allow EVERYBODY to read the file.
And you don't need Windows TFTP client, unless you're using it to test your TFTP server. I seem to recall Windows TFTP client has a habit of setting the file it gets as read-only - just be aware of that.
Please click Helpful if this post helped you and Select as Solution (drop down menu at top right of this reply) if this answered your query.
------------------------------
TAC recommended codes for AireOS WLC's and TAC recommended codes for 9800 WLC's
Best Practices for AireOS WLC's, Best Practices for 9800 WLC's and Cisco Wireless compatibility matrix
Check your 9800 WLC config with Wireless Config Analyzer using "show tech wireless" output or "config paging disable" then "show run-config" output on AireOS and use Wireless Debug Analyzer to analyze your WLC client debugs
Field Notice: FN63942 APs and WLCs Fail to Create CAPWAP Connections Due to Certificate Expiration
Field Notice: FN72424 Later Versions of WiFi 6 APs Fail to Join WLC - Software Upgrade Required
Field Notice: FN72524 IOS APs stuck in downloading state after 4 Dec 2022 due to Certificate Expired
- Fixed in 8.10.196.0, latest 9800 releases, 8.5.182.12 (8.5.182.13 for 3504) and 8.5.182.109 (IRCM, 8.5.182.111 for 3504)
Field Notice: FN70479 AP Fails to Join or Joins with 1 Radio due to Country Mismatch, RMA needed
How to avoid boot loop due to corrupted image on Wave 2 and Catalyst 11ax Access Points (CSCvx32806)
Field Notice: FN74035 - Wave2 APs DFS May Not Detect Radar After Channel Availability Check Time
Leo's list of bugs affecting 2800/3800/4800/1560 APs
Default AP console baud rate from 17.12.x is 115200 - introduced by CSCwe88390
