01-28-2019 08:15 PM - edited 07-05-2021 09:45 AM
Hello
I convert from 8.3.111 AP 1815i CAPWAP to moblity express 8.8.100
But i have a problem :
switch layer 2 can ping to Cisco mobility express WLC and my Laptop can pingto Cisco mobility express WLC
but WLC moblity express can't ping the switch ni Laptop and not broadcast SSID and can't get to Web GUI
anyone had this kind of issue with AP 1815i CME?
Urgent , i must to resolve this problem So ,
how i can reslove this CME that allow ME ping to switch and laptop and i can get Web GUI ?????????????
thanks in advance
01-30-2019 12:31 AM
i send yo file version 8.3.111 AP 1815i
if this version can convertir to 8.8.100 or 8.8.111 ???????
01-30-2019 12:32 AM
send yo file version 8.3.111 AP 1815i
if this version can convertir to 8.8.100 or 8.8.111 ??????? to ME ?
cisco AIR-AP1815I-I-K9 ARMv7 Processor rev 5 (v7l) with 1015956/851260K bytes of--More-- memory.
--More-- Processor board ID FGL2221B268
--More-- AP Running Image : 8.3.111.0
--More-- Primary Boot Image : 8.3.111.0
--More-- Backup Boot Image : 0.0.0.0
--More-- 1 Gigabit Ethernet interfaces
--More-- 2 802.11 Radios
--More-- Radio FW version : 8edf74e05d634a962e683454e8fc1be2
--More-- NSS FW version : not available
--More--
--More-- Base ethernet MAC Address : 78:0C:F0:DB:2A:90
--More-- Part Number : 0-0000-00
--More-- PCA Assembly Number : 074-105850-02
--More-- PCA Revision Number : 0
--More-- PCB Serial Number : FOC22195ZNM
--More-- Top Assembly Part Number : 074-105850-02
--More-- Top Assembly Serial Number : FGL2221B268
--More-- Top Revision Number : A0
--More-- Product/Model Number : AIR-AP1815I-I-K9
--More--
01-30-2019 12:53 AM
01-30-2019 12:59 AM
yes i know , if i convertir to 8.8.111 , then i can do acces per interface web !!
i used anthoer AP1815i to convertir 8.8..11 Bu the AP1815i that i used 8.8.100 , what solution i can do that , f convertir to capwap ????????, what i do exactly
01-30-2019 01:41 AM
01-30-2019 04:25 AM
i ued a solution :
controller> I used Backup boot image 8.8.111 and then i convert to 8.8.100 : Then it is fine !!
--------------Show boot---------------
Primary Boot Image............................... 8.8.100.0 (default) (active)
Backup Boot Image................................ 8.8.111.0
But other Problem : i need command to show AP 1815i from CLI ME 1815 and i need command that allow AP detect WLC 1815 and ME detct AP 1815i
so what command used : please i need you help
01-30-2019 04:33 AM
i ued a solution :
controller> I used Backup boot image 8.8.111 and then i convert to 8.8.100 : Then it is fine !!
--------------Show boot---------------
Primary Boot Image............................... 8.8.100.0 (default) (active)
Backup Boot Image................................ 8.8.111.0
But other Problem : i need command to show AP 1815i from CLI ME 1815 and i need command that allow AP detect WLC 1815 and ME detct AP 1815i
so what command used : please i need you help
01-30-2019 04:42 AM
What command can be used in the controller ME that AP associated to controller and that controller associated to acces point????????????,
01-30-2019 04:43 AM
01-30-2019 05:04 AM
ME is actually 8.8.100 active and 8.8.111 boot image Backup
--------------Show boot---------------
Primary Boot Image............................... 8.8.100.0 (default) (active)
Backup Boot Image................................ 8.8.111.0
ME ( controller ) with 8.8.100
===> So other r AP 1815i with by default 8.3.111 :
if convert 8.3.111 to 8.8.111 that allow ME and AP communicate ???? or not ???,,
OR i used other command CLI in ME 1815i that allow AP and ME communicate between them ????
what i can do !!
thanks in advance
01-30-2019 05:05 AM
ME is actually 8.8.100 active and 8.8.111 boot image Backup
--------------Show boot---------------
Primary Boot Image............................... 8.8.100.0 (default) (active)
Backup Boot Image................................ 8.8.111.0
ME ( controller ) with 8.8.100
===> So other r AP 1815i with by default 8.3.111 :
if convert 8.3.111 to 8.8.111 that allow ME and AP communicate ???? or not ???,,
OR i used other command CLI in ME 1815i that allow AP and ME communicate between them ????
what i can do !!
thanks in advance
01-30-2019 05:20 AM
01-30-2019 09:12 AM
NO, i want on one ME 1815I running now 8.8.100 : ( it is ok and it is fine ) BUT and other AP ( 29 AP 1815i) CAPWAPr now running by default 8.3.111
Then , i ask you , what i can do that allow ME 1815I communicate with other AP 1815i and vers versa ???????,
problem 1) what command used in WLC ME ?????? or other method that allow communicaton?
2)Problem 2) SSID is show in etlehphone but password is not accpted : ( password is the same configure ME ) : seconde problem
there two probleme
so please , what two solution can resolve ????,, ( it must this week finish this project )
thanks
01-30-2019 09:19 AM
01-30-2019 09:25 AM
1) i send you a file that show version AP1815I new
2) ME 8.8.100 : i set : username : AP-SOTETEL + Password : Sotetel123 ( these settings requests when converter from 8.8.11 AP to ME 8.8.100 )
But , i try in pc or telehpne portabl : password don'work !!!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide