11-22-2017 10:49 AM - edited 07-05-2021 07:54 AM
Hello,
I am having two 5520's. The primary wlc has License type: Permanent and count 920.
The secondary show Lic: Evaluation and count 1500 Licensing Expires: 12 weeks.
Now if the primary fails, is there any way the AP's register with secondary WLC even after 12 weeks?
If we have on active and standby setup, will the licence file also be supported or its per device base.
Is there any way to effectively use this lic.
Regards,
Satya.Mothukuri
Solved! Go to Solution.
11-22-2017 10:46 PM
Correct.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html
In HA SSO mode you dont nee dto menstion primary and econdary WLC IP under HA tab.
Regards
Dont forget to rate helpful posts
11-23-2017 03:18 AM
Hi Satya,
When the WLC is in HA SSO, then there is no special config required on the AP level. This is box level Redundancy. Meaning, one of the WLC will acts as active and the secondary will remain Standby until the failover happens.
On the Licensing, the Secondary WLC needs minimum of 50 AP count or HA SKU license to enable SSO. During failover the secondary WLC will inherit the primary Controllers license and becomes active
Note: If you are using Eval license, post 12 weeks if the secondary WLC gets reboots manually or due to some trigger then it will lose the licensing info. Hence, it is always suggested to have permanent license of 50 AP count/HA SKU.
Regards,
Divya
11-22-2017 11:54 AM
@satya mothukuri wrote:
If we have on active and standby setup, will the licence file also be supported or its per device base.
Hi Satya,
Only if both units were configured for HA SSO.
11-22-2017 10:42 PM
Thanks for your reply.
so in HA mode, the standby take over the license if the primary fail?the standby doesn’t need any license?
In HA mode, what is the AP congfiguration settings for High availability? I mean do we mention the primary controllers IP as active controller ip in HA pair and secondary controller ip as standby controller ip???
11-22-2017 10:46 PM
Correct.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html
In HA SSO mode you dont nee dto menstion primary and econdary WLC IP under HA tab.
Regards
Dont forget to rate helpful posts
11-23-2017 03:18 AM
Hi Satya,
When the WLC is in HA SSO, then there is no special config required on the AP level. This is box level Redundancy. Meaning, one of the WLC will acts as active and the secondary will remain Standby until the failover happens.
On the Licensing, the Secondary WLC needs minimum of 50 AP count or HA SKU license to enable SSO. During failover the secondary WLC will inherit the primary Controllers license and becomes active
Note: If you are using Eval license, post 12 weeks if the secondary WLC gets reboots manually or due to some trigger then it will lose the licensing info. Hence, it is always suggested to have permanent license of 50 AP count/HA SKU.
Regards,
Divya
11-24-2017 09:07 AM
Hello Divya,
Thanks for reply, So
1. if purchase 50 Lic for secondary, will that do good? Because the primary is handing 700 AP's now.
How will the lic file transfer during the primary failure? any manual intervene required?
2. When we have this HA configured, will they have any VIP IP?? so that in the AP--> high availability tab we no need to have secondary controller IP.
Regards,
Satya.Mothukuri
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide