Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I have a router that has an integrated AP. It is running an Lightweight image (w8). I want to switch to autonomous (w7) but there is no w7 image in the flash. I found some instruction about enabling the CLI and use "archive download-sw". But for some...
Hello Can anybody tell me if it is possible to modify the height of a building map in Prime 3.4?We have a situation where we need to adjust the height of an imported building from of 3m to 5.5m. I don't appear to be able to re-adjust this height with...
Hi All,Need help for configuring 9800-40 standalone WLC. We have done bootup config for WLC. Also able to access through http. We defined dayzero config through GUI. Once we finish it , we got message configuration successfully applied then login pag...
Dear AllPlease see my description and provide a solutionAssume that i have three sites (Site A, Site B, Site C) and i have multiple end users at Site C Site C receiving Bandwidth from Site B and Site A Via Radio LinkHow can we configure a switch as S...
Resolved! AIR-CAP 1702I-D-K9 configuration
I tried to configure a new AirCap 1702I-D-K9. It has an IP address from the local dhcp server. But I could not login via putty ssh or windows telnet. the error for ssh is access denied I entered username / password as Cisco / Cisco also I did telne...
Hello Experts, I wanted to get your opinion based on your experience deploying wireless networks in large distribution Centers.Our client warehouses are very large in size and many of them include rack tunnels or mezzanines between rack shelves.Whil...
Hi everyone,I read a released note version 8.0.150.0 already but in release note I don't see how to upgrade version 8.0.110.0 to 8.0.150.0.I found Upgrading from Cisco MSE Release 8.0.120.0 through 8.0.140.9 to Cisco MSE to 8.0.150.x can I upgrade to...
We currently use UDP Broadcasts for a service in our wired network to minimize traffic as we communicate with several hundred devices. Looking at what I can find on 802.11 without paying for a copy of the standard, it appears that in the case of devi...
Our WLAN has several Mobility Anchors to differnt organisations.We are running severak 8510 on 8.0.151 and 5520 on 8.5.140.One of the orgnisations we have anchors to has 5508 and just upgraded to 8.5.151. Since then seem to have intermittent issues b...
Hello -We have a 1562 ME 8.5 with gi0/0/1(DS) showing BILLIONS of tx/rx errors/discards in SolarWInds.The Master AP is directly connected to a Fortigate FW on a untrusted port natted to a trusted IP address.Wired0 has no packet drops & the device is ...
Hello team,Did do somebody reports in Cisco Prime (3.6) for monitoring alarm about status Cisco ISE, WLC, ASA?For exemple, my Cisco WLC is going down and Prime create and sent me to email about it. I haven't found it yet in Cisco Prime reports. Thank...
Hi there,I'm planning to upgrade a set of APs for a customer. These APs are model MR42 and they're currently in production, so customer and I agreed to upgrade one only AP by first in order to analyze its behavior and later proceed to a maintenance w...
I am attempting to create a guest Wi-Fi SSID using ISE 2.0 with a hotspot portal. I have been asked if we can capture the email address and also if possible to add a second tick box asking if our charity can contact the person using the wi-fi via ema...
Resolved! MR74 - Smart RF
Hi ,We have recently had a wireless survey completed and they have recommended using Meraki MR74 access points configured to Smart RF .I have been unable to find any documentation / setting to configure the AP's in this mode - can anyone offer any he...
Hi, I have a AIR-AP2802I-B-K9C which I am trying to setup. The image is Mobility Express and the initial setup seems to have worked. I can get to the GUI and have set DHCP Scopes and WLANs. The issue I am seeing is the 2nd SSID does not broadcast and...
