02-19-2013 09:37 AM
Hello XR Gurus,
We are currently doing some tests with internet full routing inside two VRFs and we are encountering some issues that we would like you to help.
Scenario:
IOS-XR with 4.2.3 P image
Trident LCs
RSP-4G
Only Two VRFs configured on the box, both with full routing
Issue:
We are sending 450K V4 prefixes, plus 25K V6 prefixes with 65K /24 prefixes per each /8, which should be inside the subtree limits. Still we are getting the following error message:
LC/0/0/CPU0:Feb 19 16:42:55.833 : prm_server_tr[295]: %PLATFORM-NP-3-OOR : Routing Table Full : PRM failed to install a route (114.255.239.0/24) because the subtree was full. Each subtree is limited to 262144 routes per subtree.Subtree where install failed is 114.0.0.0/8
Although, we get this error message we can see the prefix installed on CEF HW:
RP/0/RSP0/CPU0:A9K-LAB02#
RP/0/RSP0/CPU0:A9K-LAB02#show cef vrf publico hardware ingress location 0/4/CPU0 | i 114.255.239.0/24
Tue Feb 19 17:04:40.589 WET
114.255.239.0/24 101.101.101.2 <recursive>
RP/0/RSP0/CPU0:A9K-LAB02#
RP/0/RSP0/CPU0:A9K-LAB02#
Can anyone help us???
Thanks!!!
Cheers,
Pedro
02-19-2013 11:40 AM
Hi,
Let us know what smu running on your router. Following output might be useful
show platform
show install active summary
Also check you have all the SMU recommended @
http://www.cisco.com/web/Cisco_IOS_XR_Software/pdf/ASR9000_423_Release_Recommendation.pdf
Thanks
Parthiv
02-20-2013 02:39 AM
Hi Parthiv,
Yes we have pretty much all the recommended SMUs installed. Requested outputs are below:
RP/0/RSP0/CPU0:A9K-LAB02(admin)#show platform
Wed Feb 20 10:32:46.135 WET
Node Type State Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0 A9K-RSP-4G(Active) IOS XR RUN PWR,NSHUT,MON
0/RSP1/CPU0 A9K-RSP-4G(Standby) IOS XR RUN PWR,NSHUT,MON
0/FT0/SP FAN TRAY READY
0/FT1/SP FAN TRAY READY
0/0/CPU0 A9K-4T-B IOS XR RUN PWR,NSHUT,MON
0/1/CPU0 A9K-4T-B IOS XR RUN PWR,NSHUT,MON
0/4/CPU0 A9K-40GE-B IOS XR RUN PWR,NSHUT,MON
0/PM0/SP A9K-2KW-DC READY PWR,NSHUT,MON
0/PM1/SP A9K-2KW-DC READY PWR,NSHUT,MON
0/PM3/SP A9K-2KW-DC READY PWR,NSHUT,MON
0/PM4/SP A9K-2KW-DC READY PWR,NSHUT,MON
RP/0/RSP0/CPU0:A9K-LAB02(admin)#
RP/0/RSP0/CPU0:A9K-LAB02(admin)#show install active summary
Wed Feb 20 10:32:47.822 WET
Default Profile:
SDRs:
Owner
Active Packages:
disk0:asr9k-p-4.2.3.CSCud37351-1.0.0
disk0:asr9k-p-4.2.3.CSCud29892-1.0.0
disk0:asr9k-mini-p-4.2.3
disk0:asr9k-doc-p-4.2.3
disk0:asr9k-p-4.2.3.CSCub22596-1.0.0
disk0:asr9k-k9sec-p-4.2.3
disk0:asr9k-p-4.2.3.CSCuc17410-1.0.0
disk0:asr9k-mpls-p-4.2.3
disk0:asr9k-mgbl-p-4.2.3
disk0:asr9k-mcast-p-4.2.3
disk0:asr9k-p-4.2.3.CSCud07536-1.0.0
disk0:asr9k-p-4.2.3.CSCub74517-1.0.0
disk0:asr9k-p-4.2.3.CSCub96985-1.0.0
disk0:asr9k-p-4.2.3.CSCud54093-1.0.0
RP/0/RSP0/CPU0:A9K-LAB02(admin)#
Thanks!!
02-20-2013 01:32 PM
Could you try following config.
vrf <> mode big
Please provide following
show cef ipv4 summary location all
show cef ipv6 summary location all
show tech cef
Thanks
Parthiv
02-22-2013 07:28 AM
Hi Parthiv,
Strangely (or not) it worked with "mode big"... However I do not understand why, since I only have two VRFs configured on the router. Any idea?
Do you still want the requested outputs?
Cheers,
Pedro
02-22-2013 08:38 AM
Hi Parthiv,
we did some more tests with and without "mode big". Please take a look at the bellow output:
RP/0/RSP0/CPU0:A9K-LAB02#conf t
RP/0/RSP0/CPU0:A9K-LAB02(config)#vrf telepac
RP/0/RSP0/CPU0:A9K-LAB02(config-vrf)#mode big
RP/0/RSP0/CPU0:A9K-LAB02(config-vrf)#commit
Fri Feb 22 15:37:16.352 WET
RP/0/RSP0/CPU0:A9K-LAB02(config-vrf)#
RP/0/RSP0/CPU0:A9K-LAB02#
RP/0/RSP0/CPU0:A9K-LAB02#show uid data location 0/4/CPU0 GigabitEthernet0/4/0/23 ingress | i Table Fri Feb 22 15:38:42.259 WET
Table ID 0x200
RP/0/RSP0/CPU0:A9K-LAB02#conf
Fri Feb 22 15:39:51.002 WET
RP/0/RSP0/CPU0:A9K-LAB02(config)#
RP/0/RSP0/CPU0:A9K-LAB02(config)#vrf telepac
RP/0/RSP0/CPU0:A9K-LAB02(config-vrf)#no mode big
RP/0/RSP0/CPU0:A9K-LAB02(config-vrf)#commit
Fri Feb 22 15:39:57.583 WET
RP/0/RSP0/CPU0:A9K-LAB02(config-vrf)#
RP/0/RSP0/CPU0:A9K-LAB02#show uid data location 0/4/CPU0 GigabitEthernet0/4/0/23 ingress | i Table Fri Feb 22 15:40:00.285 WET
Table ID 0x1200
RP/0/RSP0/CPU0:A9K-LAB02#conf
Fri Feb 22 15:40:15.187 WET
RP/0/RSP0/CPU0:A9K-LAB02(config)#
RP/0/RSP0/CPU0:A9K-LAB02(config)#vrf telepac
RP/0/RSP0/CPU0:A9K-LAB02(config-vrf)#mode big
RP/0/RSP0/CPU0:A9K-LAB02(config-vrf)#commit
Fri Feb 22 15:40:19.577 WET
RP/0/RSP0/CPU0:A9K-LAB02(config-vrf)#exit
RP/0/RSP0/CPU0:A9K-LAB02(config)#exit
RP/0/RSP0/CPU0:A9K-LAB02#show uid data location 0/4/CPU0 GigabitEthernet0/4/0/23 ingress | i Table
Fri Feb 22 15:40:23.947 WET
Table ID 0x300
RP/0/RSP0/CPU0:A9K-LAB02#admin
Fri Feb 22 15:40:28.559 WET
RP/0/RSP0/CPU0:A9K-LAB02(admin)#reload location all Fri Feb 22 15:40:32.356 WET
Preparing system for backup. This may take a few minutes especially for large configurations.
Status report: node0_RSP0_CPU0: START TO BACKUP
Status report: node0_RSP0_CPU0: BACKUP HAS COMPLETED SUCCESSFULLY [Done] Proceed with reload? [confirm]
This node received reload command. Reloading in 5 secs
Connection to 172.25.200.6 closed by foreign host.
bash-3.00#
bash-3.00#
bash-3.00#
bash-3.00# telnet 172.25.200.6
Trying 172.25.200.6...
Connected to 172.25.200.6.
Escape character is '^]'.
User Access Verification
Username: admin
Password:
RP/0/RSP0/CPU0:A9K-LAB02#
RP/0/RSP0/CPU0:A9K-LAB02#
RP/0/RSP0/CPU0:A9K-LAB02#show uid data location 0/4/CPU0 GigabitEthernet0/4/0/23 ingress | i Table
Fri Feb 22 15:58:04.109 WET
Table ID 0x200
Any comment?
Cheers,
PM
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: