Hi I have created the following on a asr9k 4.3.1:I connected both the RSP0 and RSP1's mgmt 0 Ethernet ports to a seperate L2 switch for Out of band management.entered the following commands on the asr:vrf MANRingdescription Management network! ...
Hello,Can we configure the same vlan id on two different physical interfaces on a ASR9010?I found this in the documentation page 1022:http://www.cisco.com/en/US/docs/routers/crs/software/crs_r4.3/interfaces/command/reference/b_interfaces_cr43xcrs.pdf...
Hi We are in the configuration stage of testing the BNG functional on a ASR9006, so we've configured the PPPoE session termination and all works fine.Second phase we want subscribers to be redirected to a portal via a radius server when accounts are...
Hi fellows,I want to configure udld with subsecond failure detection on link between asr9k and nexus 7k. I was searching in Cisco documentation but didn't find commands to configure fast hello like in cat6500. Timer is configured with message-time th...
Hi, I have an environment where you have a ME3800 and an ASR9000 as PEs for mVPN.Within the VPN the control and data plane for ipv4 works just fine. That is I can ping from a loopback on ME3800 to the 9000 (both on a VRF).regarding the core and mVPN ...
Hi Guys, i am new to XR IOS, just recently deployed some 9001 XR on our network, had a prblem recently where one devices interfaces loose traffic, all the neighbours go down as per the below log, i am trying to find the reason for this as it keeps ha...
I detected the flash is inserted but i don't know how to access the flash drive. Pls help.RP/0/RSP0/CPU0:Jul 2 15:22:44.077 : umass-enum[97]: Flash device inserted
Hi all,Sometimes observed the ASR9K 10G high traffic, just want to know what type of traffic are, any waus to check the source and destination IP and its protocal. Tks in advance
ASR 9k having SFP stucking problem. Link shows up in console but cant ping even simple point to point. Work arround is plug out and in SFP so ping reply start getting. Is there any way I can re initialed perticular SFP only using command line for exp...
Hi,We are monitoring a BGP peering flap for a fraction of seconds approximately every three days for a particular neighbor. We are seeing this behavior consistently for a Month.Jun 10 08:55:15.566 NST: bgp[1041]: %ROUTING-BGP-5-ADJCHANGE : neighbor ...
HiI have a little confusion on ASR9k. we dont have ISM module on ASR9K so we're going to enable NAT444 (CG) , we're not sure this feature can support on this platform without ISM with XR 4.3 MPLS software. Would you please someone to resolve my doubt...
Hello all,I'm trying to find info regarding the power consumption of a CRS. However I cannot find any information about the following CRS modules (no datasheet):CRS-8-FC/SCRS-8-FC-140/SCRS-8-LCC-FAN-TRAny idea of where can I find this info?Thanks!Che...
when install smu, some smu modify the timers in hsrp? or this synchronizes the configuration whit other Equipment?the smu installesd is: disk0:asr9k-p-4.0.1.CSCua63591-1.0.0 disk0:asr9k-p-4.0.1.CSCty86177-1.0.0 disk0:asr9k-p-4.0.1.CSCts10657...
Hi All,I have to install transceivers ER in one ASR9010 and I have available two types: XFP-10GER-192IR+ and XFP10GER-192IR-L. I saw the compatibility matrix document and it says that I can use both types in one 8X10G Linecard. So my question is what...
