cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2091
Views
5
Helpful
2
Replies

ASR 9000 400G SE combo line card | A9K-4HG-FLEX-SE

Nikko_Boco3279
Level 1
Level 1

Hi there,

Can someone share a valid configuration guide to activate 40Gb interfaces in the A9K-4HG-FLEX-SE linecard?

Thanks,

 

1 Accepted Solution

Accepted Solutions

smilstea
Cisco Employee
Cisco Employee

Here is an example:

hw-module location 0/1/cpu0 slice 0 config-mode 1x40GE,1x40GE,1x40GE,1x40GE

 

Possible configurations:

RP/0/RSP0/CPU0:router#sh controllers np valid-port-groups np0 location 0/1/cpu0
Node: 0/1/CPU0:
----------------------------------------------------------------

NP0: Valid Port Groups
----+---------------------+---------------------+---------------------+---------------------
SEL | Group 0 | Group 1 | Group 2 | Group 3
----+---------------------+---------------------+---------------------+---------------------
DFLT 1x100GE 1x100GE 1x100GE 1x100GE
1 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE
2 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 10x10GE/5x1GE_5x10GE
3 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE
4 1x100GE/1x40GE/4x25GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE
5 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE
Notes:
DFLT : QSFP port 40, QSFP port 41, QSFP port 42, QSFP port 43 (default)
Group 0: QSFP port 40 or SFP10g port 0-9 or SFP10g port 0-4 SFP1g port 5-9 or SFP25g port 6-9
Group 1: QSFP port 41 or SFP10g port 10-19 or SFP10g port 10-14 SFP1g port 15-19 or SFP25g port 16-19
Group 2: QSFP port 42 or SFP10g port 20-29 or SFP10g port 20-24 SFP1g port 25-29 or SFP25g port 26-29
Group 3: QSFP port 43 or SFP10g port 30-39 or SFP10g port 30-34 SFP1g port 35-39 or SFP25g port 36-39

 

Thanks,

Sam

 

View solution in original post

2 Replies 2

smilstea
Cisco Employee
Cisco Employee

Here is an example:

hw-module location 0/1/cpu0 slice 0 config-mode 1x40GE,1x40GE,1x40GE,1x40GE

 

Possible configurations:

RP/0/RSP0/CPU0:router#sh controllers np valid-port-groups np0 location 0/1/cpu0
Node: 0/1/CPU0:
----------------------------------------------------------------

NP0: Valid Port Groups
----+---------------------+---------------------+---------------------+---------------------
SEL | Group 0 | Group 1 | Group 2 | Group 3
----+---------------------+---------------------+---------------------+---------------------
DFLT 1x100GE 1x100GE 1x100GE 1x100GE
1 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE
2 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 10x10GE/5x1GE_5x10GE
3 1x100GE/1x40GE/4x25GE 1x100GE/1x40GE/4x25GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE
4 1x100GE/1x40GE/4x25GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE
5 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE 10x10GE/5x1GE_5x10GE
Notes:
DFLT : QSFP port 40, QSFP port 41, QSFP port 42, QSFP port 43 (default)
Group 0: QSFP port 40 or SFP10g port 0-9 or SFP10g port 0-4 SFP1g port 5-9 or SFP25g port 6-9
Group 1: QSFP port 41 or SFP10g port 10-19 or SFP10g port 10-14 SFP1g port 15-19 or SFP25g port 16-19
Group 2: QSFP port 42 or SFP10g port 20-29 or SFP10g port 20-24 SFP1g port 25-29 or SFP25g port 26-29
Group 3: QSFP port 43 or SFP10g port 30-39 or SFP10g port 30-34 SFP1g port 35-39 or SFP25g port 36-39

 

Thanks,

Sam