01-27-2020 02:20 AM
Hello Cisco community,
I am trying to lab VXLAN on 3 routers - 2x ASR9910 and 1x ASR9006 with IOS-XR 5.3.3
All of them should support VXLAN encasulation and BUM replication over multicast. Unfortunately it works only on newer ASR9910. Those 2 routers does not see ASR9006 in nve peers and it looks like ASR9006 is not able to encapsulate and send traffic over VXLAN.
Is it possible that I am missing the licensing? I found out that there is a RTU: Part #: S-A9K-VXLN-RTU-10 ASR 9000 VxLAN 10Gbps Right to Use License
But it works on ASR9910 without any license..
Thank You.
Bridge group: vxlan-test, bridge-domain: vlan88, id: 2, state: up, ShgId: 0, MSTi: 0 Coupled state: disabled MAC learning: enabled MAC withdraw: enabled MAC withdraw for Access PW: enabled MAC withdraw sent on: bridge port up MAC withdraw relaying (access to access): disabled Flooding: Broadcast & Multicast: enabled Unknown unicast: enabled MAC aging time: 300 s, Type: inactivity MAC limit: 4000, Action: none, Notification: syslog MAC limit reached: no MAC port down flush: enabled MAC Secure: disabled, Logging: disabled Split Horizon Group: none Dynamic ARP Inspection: disabled, Logging: disabled IP Source Guard: disabled, Logging: disabled DHCPv4 snooping: disabled IGMP Snooping: enabled IGMP Snooping profile: none MLD Snooping profile: none Storm Control: disabled Bridge MTU: 1500 MIB cvplsConfigIndex: 3 Filter MAC addresses: P2MP PW: disabled Create time: 24/01/2020 15:24:05 (2d19h ago) No status change since creation ACs: 1 (1 up), VFIs: 0, PWs: 0 (0 up), PBBs: 0 (0 up) List of ACs: AC: GigabitEthernet0/1/0/39.88, state is up Type VLAN; Num Ranges: 1 VLAN ranges: [88, 88] MTU 9188; XC ID 0x1880001; interworking none MAC learning: enabled Flooding: Broadcast & Multicast: enabled Unknown unicast: enabled MAC aging time: 300 s, Type: inactivity MAC limit: 4000, Action: none, Notification: syslog MAC limit reached: no MAC port down flush: enabled MAC Secure: disabled, Logging: disabled Split Horizon Group: none Dynamic ARP Inspection: disabled, Logging: disabled IP Source Guard: disabled, Logging: disabled DHCPv4 snooping: disabled IGMP Snooping: enabled IGMP Snooping profile: none MLD Snooping profile: none Storm Control: bridge-domain policer Static MAC addresses: Statistics: packets: received 8156 (multicast 4, broadcast 8148, unknown unicast 0, unicast 0), sent 432 bytes: received 1259728 (multicast 412, broadcast 1258866, unknown unicast 0, unicast 0), sent 57700 MAC move: 0 Storm control drop counters: packets: broadcast 0, multicast 0, unknown unicast 0 bytes: broadcast 0, multicast 0, unknown unicast 0 Dynamic ARP inspection drop counters: packets: 0, bytes: 0 IP source guard drop counters: packets: 0, bytes: 0 List of VNIs: VNI 10088, state is up XC ID 0x80000003 Encap type VXLAN, Data Plane L2 Service Overlay nve1, Source X.X.X.X, Multicast Group 239.239.8.8, UDP Port 4789 Anycast VTEP 0.0.0.0, Anycast Multicast Group 0.0.0.0 MAC learning: enabled Flooding: Broadcast & Multicast: enabled Unknown unicast: enabled MAC aging time: 300 s, Type: inactivity MAC limit: 4000, Action: none, Notification: syslog MAC limit reached: no MAC port down flush: enabled MAC Secure: disabled, Logging: disabled Split Horizon Group: none Dynamic ARP Inspection: disabled, Logging: disabled IP Source Guard: disabled, Logging: disabled DHCPv4 snooping: disabled IGMP Snooping: enabled IGMP Snooping profile: none MLD Snooping profile: none Storm Control: bridge-domain policer Statistics: packets: received 432 (unicast 0), sent 0 bytes: received 57700 (unicast 0), sent 0 MAC move: 0 List of Access PWs: List of VFIs:
Solved! Go to Solution.
01-29-2020 09:47 AM
01-27-2020 10:28 AM
What is the show platform from all 3 routers?
Thanks,
Sam
01-28-2020 01:32 AM
Hi,
#sh platform
Tue Jan 28 10:30:02.409 utc
Node Type State Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0 A99-RSP-TR(Active) IOS XR RUN PWR,NSHUT,MON
0/RSP1/CPU0 A99-RSP-TR(Standby) IOS XR RUN PWR,NSHUT,MON
0/0/CPU0 A9K-MOD160-TR IOS XR RUN PWR,NSHUT,MON
0/0/0 A9K-MPA-8X10GE OK PWR,NSHUT,MON
0/0/1 A9K-MPA-2X40GE OK PWR,NSHUT,MON
0/3/CPU0 A9K-4T16GE-TR IOS XR RUN PWR,NSHUT,MON
0/7/CPU0 A9K-MOD160-TR IOS XR RUN PWR,NSHUT,MON
0/7/0 A9K-MPA-8X10GE OK PWR,NSHUT,MON
0/7/1 A9K-MPA-2X40GE OK PWR,NSHUT,MON
#sh platform
Tue Jan 28 10:30:43.377 utc
Node Type State Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0 A99-RSP-TR(Active) IOS XR RUN PWR,NSHUT,MON
0/RSP1/CPU0 A99-RSP-TR(Standby) IOS XR RUN PWR,NSHUT,MON
0/0/CPU0 A9K-MOD160-TR IOS XR RUN PWR,NSHUT,MON
0/0/0 A9K-MPA-8X10GE OK PWR,NSHUT,MON
0/0/1 A9K-MPA-2X40GE OK PWR,NSHUT,MON
0/1/CPU0 A9K-4T16GE-TR IOS XR RUN PWR,NSHUT,MON
0/3/CPU0 A9K-40GE-TR IOS XR RUN PWR,NSHUT,MON
0/4/CPU0 A9K-40GE-TR IOS XR RUN PWR,NSHUT,MON
0/5/CPU0 A9K-36x10GE-TR IOS XR RUN PWR,NSHUT,MON
0/6/CPU0 A9K-4T16GE-TR IOS XR RUN PWR,NSHUT,MON
0/7/CPU0 A9K-MOD160-TR IOS XR RUN PWR,NSHUT,MON
0/7/0 A9K-MPA-8X10GE OK PWR,NSHUT,MON
0/7/1 A9K-MPA-2X40GE OK PWR,NSHUT,MON
ASR9006
#sh platform
Tue Jan 28 10:30:59.411 utc
Node Type State Config State
-----------------------------------------------------------------------------
0/RSP0/CPU0 A9K-RSP440-SE(Active) IOS XR RUN PWR,NSHUT,MON
0/RSP1/CPU0 A9K-RSP440-SE(Standby) IOS XR RUN PWR,NSHUT,MON
0/0/CPU0 A9K-40GE-B IOS XR RUN PWR,NSHUT,MON
0/1/CPU0 A9K-40GE-B IOS XR RUN PWR,NSHUT,MON
0/2/CPU0 A9K-16T/8-B IOS XR RUN PWR,NSHUT,MON
0/3/CPU0 A9K-24x10GE-TR IOS XR RUN PWR,NSHUT,MON
01-28-2020 10:19 AM
On the 9006 can you make sure that you are using LC3 for VxLAN?
The other LCs are the older trident cards (-B) and don't support VxLAN due to limited uCode space.
In fact even the typhoon based LCs have limited VxLAN support, only the 4x100, 8x100, MOD200, and MOD400 (tomahawk LCs) have full VxLAN support.
Sam
01-29-2020 12:24 AM
Thank You, I will try to test it on the typhoon card.
What do you mean by limited support? We only need L2VPNs to run over vxlan using multicast (PIM-SM) for BUM replication.
Looks like VXLAN EVPN or ingress replication is not supported even on newer ASR9910 running 6.x code
01-29-2020 09:47 AM
01-29-2020 11:59 PM
Sorry Sam, you are right VXLAN EVPN is supported.
RP/0/RSP0/CPU0:R1(config-if)#member vni 10008 host-reachabilty protocol bgp
so only ingress replication is not supported.
Thank You.
01-28-2020 03:42 PM
01-28-2020 03:57 PM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide