03-05-2014 12:37 AM
Just wondering this high end platform not supporting the range command.
Does it exist or is it not programmed to support ?
03-05-2014 07:23 AM
Range cmd is not supported, you need to take help from tools or TCL to configure range of intfs.
03-05-2014 07:38 AM
Hi Mohammad,
I came across one tool on the internet which helps build configurations to large scale. You can use tools like CGT-Network Tools . They also have a paid version to generate config on ios and ios xr. They have a free version for IOS . I tried it, its good. It will help you generate configurations very fast. Things that took me one hour to do , I do in 2-3 minutes now.
Check out this link
hope that helps.
regards,
Tarique.
06-19-2019 04:42 PM
you can upload the setup.exe, i search and the web are broken for the download link
07-01-2020 08:33 AM
Hi @Tarique Shakil that link you provided is not working.
03-05-2014 09:20 AM
hi Mohammad,
We do have an alternative feature that is useful for very large and repetitive configurations on the ASR 9000, called
FlexCLI where we have the abaility to create config groups and apply them to multiple interfaces. This feature came out in 4.3.1 and has enhancements in 5.1.x IOS XR code
Here is the 4.3.1 FlexCLI config guide
An example of configuring common ISIS parameters for bundle interfaces:
1)configure a group:
group ISIS
router isis 'BB3'
interface 'Bundle-Ether.*'
circuit-type level-2-only
point-to-point
hello-padding disable
hello-password keychain test123
!
!
end-group
2) apply the group
config t
apply-group ISIS
commit
end
3)use the "inheritance" command to show theinherited config on ISIS Bundle-ether.* interfaces, the ## indicates
inherited configuration from the group ISIS:
RP/0/RSP0/CPU0:ASR9K#sho run router isis inheritance detail
Thu Mar 6 08:59:10.819 UTC
router isis BB3
is-type level-2-only
net 49.8760.0000.0000.0001.00
address-family ipv4 unicast
metric-style wide
maximum-paths 16
!
interface Bundle-Ether110
## Inherited from group ISIS
circuit-type level-2-only
## Inherited from group ISIS
point-to-point
## Inherited from group ISIS
hello-padding disable
## Inherited from group ISIS
hello-password keychain test123
!
interface Bundle-Ether300
## Inherited from group ISIS
circuit-type level-2-only
## Inherited from group ISIS
point-to-point
## Inherited from group ISIS
hello-padding disable
## Inherited from group ISIS
hello-password keychain test123
!
interface Bundle-Ether400
## Inherited from group ISIS
circuit-type level-2-only
## Inherited from group ISIS
point-to-point
## Inherited from group ISIS
hello-padding disable
## Inherited from group ISIS
hello-password keychain test123
!
interface GigabitEthernet0/0/0/14
address-family ipv4 unicast
!
The above example is from 5.1.1 XR code on an ASR 9000. FlexCLI is very useful for very large configurations, especially with MPLS-TE interfaces, etc
regards,
david
05-18-2016 05:39 PM
XR 5.3.2 we were seeing the 'interface-range' command, but in XR 5.3.3, it's missing.
05-18-2016 06:30 PM
hi Andy,
There is a SMU and a Service Pack to fix this issue in 5.3.3, depending on if you are using SMU's or Service Pack's. You can download them from the SW download section on www.cisco.com
asr9k-px-5.3.3.CSCux78222.pie
or
asr9k-px-5.3.3.sp1.pie
regards,
David
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: