Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2260160members
2701156discussions

Featured Content

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Proposed Configuration Change from L3SW to L2SW

In the configuration below, L3SW#1 and L3SW#2 are configured with HSRP on the VLAN 100 segment, while L3SW#3 has the VLAN 200 and VLAN 300 segments assigned to its downlinks and performs inter-VLAN routing.Endpoints are connected to the L2 switches.I...

CHISHIUNG_0-1781102345567.png
CHISHIUNG by • Level 2
  • 65 Views
  • 2 replies
  • 0 Helpful votes

Resolved! IOSvL nodes and disabled switchports

I've configured multiple OSPF labs, in CML, using the IOSvL node...disabling switchports on those nodes in each lab. (The labs have not been deleted.) When I configured an OSPFv3 lab (my third OSPF lab), initially, the two disabled switchports on two...

DTE PRO by • Community Member
  • 379 Views
  • 15 replies
  • 0 Helpful votes

Meraki MX - Show Concurrent Device History for Sizing

Is there a way in the Meraki Dashboard to show the concurrent device history? I'm looking to see the max amount of online connected devices on my network. All summary pages show either unique or max but those numbers don't seem to account for online ...

MRush5 by • Frequent Visitor
  • 41 Views
  • 0 replies
  • 0 Helpful votes

Security Intelligence - Block List - Bogon

Does anyone know if it's normal for the Cisco Talos Feed to have 0 objects in the BOGON list?  I found when mousing over the "Bogon" in the block list it shows 0 objects.  In FMC, this is under Access Policy > Security Intelligence > Block List.Secur...

a.png
davidb84 by • Frequent Visitor
  • 28 Views
  • 0 replies
  • 0 Helpful votes

Resolved! Use DX80 camera with laptop ?

Can I make the DX80 camera act as a webcam on a laptop please? I assume that the USB cable would be used.  Reason some laptops don't have a webcam and others are closed and in their docking station. Thanks Tym

tymburrow by • Community Member
  • 21458 Views
  • 11 replies
  • 0 Helpful votes

Adding new interfaces on spines to IPN

What is recommended workflow of adding new interfaces on existing spines to connect to existing IPN network. We are looking to add interface 1/60 on the existing spines to connect to existing IPN network to increase resiliency. See attached screensho...

taskmanas by • Frequent Visitor
  • 72 Views
  • 1 replies
  • 0 Helpful votes

Payload Altered with NORM Data

Hello Cisco friends,     I am having an odd issue with my new Cisco 9500s. I'm using the NORM multicast protocol and have attached a rough diagram of my current setup. I can't fully divulge specific configurations but I can try to answer any question...

seanpwhaley_0-1780930054285.jpeg

Packet capture causing reboot

Hi All Overnight I upgraded my MR to MR 32.2.3 in an effort to resolve a network issue however I have noticed that whenever I run a packet capture it causes the AP to reboot, the affected devices are MR44.So far I'm 3/3 with packets captures causing ...

C9300 Cloud Managed Wont Save Startup Config

Thought id check with the community to see if anyone else has seen this. Currently working with support to identify why we have 1 network and switch that refuses to save the startup-config. If the device reboots, it comes up with factory defaults, mi...

curtis v by • Frequent Visitor
  • 1632 Views
  • 9 replies
  • 0 Helpful votes

Checking the Number of Packets Matched by PBR

I have configured a PBR to change the next-hop destination (set ip next-hop).I believe the `show route-map` command should allow me to check the number of packets matched by the PBR, but the match counter remained at 0. Does this mean the PBR is not ...

CHISHIUNG by • Level 2
  • 83 Views
  • 1 replies
  • 0 Helpful votes

Can ping a device from secondary L3 switch but not from Primary

rimary and Secondary L3 switchesCan ping devices connected to a L3 switch on a vehicle over Fluidmesh wireless IP addresses 10.3.6.11 and 10.3.6.12 from Secondary [standby] switch.  This vlan 306 10.3.6.0/24 exists only on the vehicle.  When attempti...

LANMind69 by • Community Member
  • 251 Views
  • 7 replies
  • 0 Helpful votes
Load more