Hello, I have been configuring ASA firewall (asa v9 on Firepower 4K) to integrate with the ACI. The eBGP peerings are up and all works fine. I am trying to achieve multipath load sharing in inbound as well as outbound direction. refer to the diagra...
Hi everyone! I'm having problems upgrading the leafs and Spines switches. I already have the APICs with the last firmware but when I start the upgrading process for the switches an errors appears saying that the version is incompatible. Thanks!
Hi All, I want to migrate the access-list from old environment to ACI, below is sample of the access-list: 1 permit tcp 192.168.50.77 0.0.0.0 172.16.30.21 0.0.0.0 eq 372 permit tcp 192.168.50.77 0.0.0.0 172.16.30.22 0.0.0.0 eq 373 permit tcp 192.16...
We have migrated our WAN connections from our OLD network to ACI and have hit issues with routing loops. Hoping someone here can help. When we redistribute routes from one WAN route into our core network (now ACI) we used TAGs to prevent routing lo...
So I have a pretty vanilla service graph that I can't quite get to work. I am trying to connect EGPs client and epg2 via an ASAv with device package 1.2 but I can't get it to work. EPG client is the consumer and has a VM with an IP address of 2.2.2.2...
Hi there, Can someone from DEVNET sandboxes check the AlwaysOn ACI Simulator (https://sandboxapicdc.cisco.com/(). It does not seem to work. Best regards!
Hi, R1(AS65200)-------------ACI(AS65000)------------R2(AS65200) L0:200.200.200.1/24 L0:200.200.201.1/24 I am using the AS Override feature but I am unable to receive the route from either side...
Hi, Is it possible to run ACI Multi Site over WAN links which are optimized using WAN optimizer? As per the design guides only requirement mentioned as follows, - OSPF on the first hop routers to peer with Spine nodes - Support larger MTU Thanks
I created a bridge domain on a new fabric and for some reason im not able to communicate with the subnet configured in it. Now I know there are quite a few configuration options that could give me a problem if not done or not done correctly. My quest...
So I was digging around in ACI 3.2(1m) and I noticed that I cannot create a fault severity assignment policy like I could in 2.x. I've created monitoring policies at the tenant and fabric levels and there is literally no option to add a monitoring ob...
currently migrating Network to AVE while creating VLAN Pools required for AVE, created one pool with dynamic allocation. but, Cisco advised us to create two different VLAN ranges in the pool (i) Vlan Internal (ii) External or on Wire encapsulation ...
Hello , I am getting a bit confused with the Leaf-spine architecture for ACI. As per cisco website the Cisco Nexus 93180YC-EX Switch is considered as a ACI-leaf switch. Let's say that i have only 2 leaf switches (Cisco Nexus 93180YC-EX Switch) ...
Hello , the Cisco Nexus 93180YC-EX Switch can run either NXOS or ACI. Let's say i purchase the switch with NXOS , and later i want to deploy ACI. What is required? Should i purchase ACI licenses or is this already included.
I understand Multipod IPN should a dedicated network or in a VRF. However customer has a Multipod implementation with IPN in the global table because of some technical issues with the DCI link capability. It hasn't had any issue until the regular L3O...
So..... Turning up a couple new fabrics and I need to know how to figure how many IPs I [REALLY] need for the VTEP pool. I know that Cisco suggests 10.0.0.0/16 but do I really need to do that? Is a /22 enough? I am going to be using IPs that are non-...
