Hi Experts; Requirement is to have requests from outside as well as inside from different vlan Server to our Production Servers.At present all requests are coming from inside vlan via policy-map multi-match L3_XYZ. See Example belowpo...
-
Application Networking
(11,490) -
Community Feedback Forum
(1) -
Other Application Networking
(8) -
Other Data Center Subjects
(1) -
Other NAC
(1) -
Wide Area Application Services (WAAS)
(1,579)
Forum Posts
Hello,is there an option/command to reduce the downtime of an InlineGroup when changing the Operating Mode from Accelerating to Bypass?When I execute the "shutdown"-command at the InlineGroup it takes about 10 seconds till the InlineGroup is in Bypas...
Hi allI have 2 CSS, 1 as primary and 2nd as standby. I configured the standby CSS as my old standby CSS box and now wanted to test the faliover. I am not aware of how to test it in. ny how i have cr for that.Please suggest how to proceed further ...
Our topology is as follows:CISCO ACE 4710Two contexts A and BExternal VLAN shared, with Context A IP, Context B IP, Gateway IPWe need to make connections from rserver in context A to VIP in context B.We have created static routes in both contexts:Con...
We are converting an old CSS LB to a new ACE. Since the old CSS was in a one armed config and our application used custom port numbers I need to know how to have the ACE load balance to a server using non standard ports.Here is example.3 servers, ser...
Hello,I would like to open access to the cached content on the WAAS from a server through a Checkpoint firewall. The server has to have L3 access to the actual WAE device, from what I understand. Is this feasable? What ports would I need to...
I have a CSS 11503, version 8.02, with an SSL module. The CSS takes the SSL data, decrypts it, passes it back to the servers, and encrypts it before handing it back to the clients. Users were complaining of latency so I setup a sniffer. I am findi...
Dear,I would like to know which is the best practice scenario to load balance proxy servers:1- Best practice to have transparent proxy or proxy setting on the web browser?2- for transparent proxy: best practice to use ip wccp or route-map pointing to...
We have had the error message appear on the ACE Module log and been trying to find more information about it. Aug 1 2012 06:08:14 : %ACE-3-251027: Out of sockets THanks....
Hi.I would just like to know if you can implement Cisco WAAS on a WAN running on 128 VSAT llinks and if the performance improvement will be very significant. Significant enough to make me change my mind from upgrading the link?Thanks
Resolved! ACE ONE ARM MODE
HI,I have configured Cisco ACE 4710 in one-arm mode(physically it is in DMZ segment). I have to load balance OWA servers using ACE, these servers are physically on inside of firewall. Now, the load balancer is working fine wi...
Hello there,I configured 2 farms, and one call on a specific host adress is redirected to farm 2.This is working, but only for HTTP traffic : for HTTPS, it's redirected to farm 1 ! I need help, if someone can help...I post my configuration here :prob...
Hi , We are managing almost 20 ACE in different location in HA mode . Right now the configuration is for redundancy in ft group and ft track in user context and this redundancy are working well good . My new requirement is to track the physical inte...
HiI'm currently looking at a requirement we have to direct users to a particular VMWare broker dependent up AD credentials. An overview is that we have 2 data centers, each with a specific brokers and set of VDIs. Users are mapped to a particular dat...
We have a sharepoint 2010 on our internal network at HQ. HQ and each branch have WAAS 4.4.3.When a WAN user tries to open a MS office file (e.g. open with excel) off the sharepoint server from a branch it takes 5-10 minutes and sometimes just errors...