Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Natalie Ramirez
Stats
Member since
01-19-2012
90
Posts
9
Helpful
2
Solutions
10-19-2015
12:30 PM
I also just tried creating access list 701 access-list 701 deny 0000.0000.0000 ffff.ffff.ffff but when I attempt to apply it to the interface, I get: mac access-group 701 in % Invalid access list name. Not sure if this is a clue as to what is wrong.
... View more
10-19-2015
12:12 PM
I created an extended access list and allowed a single mac address in a conference room, so only the VoIP phone will have access with a deny any any at the end. It did not work, so I removed all permits from the list and just have a single deny any any in the access list, and have it applied to the interface on the 6509 that is in the conference room. Still, all traffic is flowing with no disruption. mac access-list extended phone deny any any interface GigabitEthernet2/14 switchport switchport access vlan 63 switchport mode access switchport voice vlan 73 mac access-group phone in end I can see both the phone and the PC with: sh mac add | inc 2/14 I can ping both the phone and the PC. How can I stop communication on a port using a mac access-list?
... View more
- Tags:
- mac access-list
Labels:
09-23-2015
12:44 PM
switch# sh logg Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disab led, filtering disabled) Console logging: level debugging, 2053 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 155 messages logged, xml disabled, filtering disabled Logging to: vty1(0) Buffer logging: level debugging, 2053 messages logged, xml disabled, filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled File logging: disabled Trap logging: level notifications, 2009 message lines logged Logging to 192.168.48.132, 2009 message lines logged, xml disabled, filtering disabled Log Buffer (4096 bytes): itEthernet1/0/13, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down 1w1d: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down 1w1d: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: IEEE PD 1w1d: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/13: Power granted 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up 1w1d: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down 1w1d: %ILPOWER-7-DETECT: Interface Gi1/0/13: Power Device detected: IEEE PD 1w1d: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/13: Power granted 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up 1w1d: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/13: PD removed 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down 1w1d: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/30: PD removed 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/30, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/30, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/23, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/23, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/23, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/23, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/23, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/23, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/23, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/23, changed state to up 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/19, changed state to down 1w1d: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/19: PD removed 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/19, changed state to down 1w1d: %ILPOWER-7-DETECT: Interface Gi1/0/19: Power Device detected: IEEE PD 1w1d: %ILPOWER-5-POWER_GRANTED: Interface Gi1/0/19: Power granted 1w1d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/19, changed state to up 1w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/19, changed state to up 1w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to down 1w2d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to down 1w2d: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/13, changed state to up 1w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/13, changed state to up
... View more
09-23-2015
12:42 PM
switch#sh pow inl Module Available Used Remaining (Watts) (Watts) (Watts) ------ --------- -------- --------- 1 370.0 48.2 321.8 Interface Admin Oper Power Device Class Max (Watts) --------- ------ ---------- ------- ------------------- ----- ---- Gi1/0/1 auto off 0.0 n/a n/a 15.4 Gi1/0/2 auto off 0.0 n/a n/a 15.4 Gi1/0/3 auto off 0.0 n/a n/a 15.4 Gi1/0/4 auto off 0.0 n/a n/a 15.4 Gi1/0/5 auto off 0.0 n/a n/a 15.4 Gi1/0/6 auto on 6.4 IP Phone 8945 2 15.4 Gi1/0/7 auto off 0.0 n/a n/a 15.4 Gi1/0/8 auto off 0.0 n/a n/a 15.4 Gi1/0/9 auto off 0.0 n/a n/a 15.4 Gi1/0/10 auto off 0.0 n/a n/a 15.4 Gi1/0/11 auto off 0.0 n/a n/a 15.4 Gi1/0/12 auto off 0.0 n/a n/a 15.4 Gi1/0/13 auto off 0.0 n/a n/a 15.4 Gi1/0/14 auto off 0.0 n/a n/a 15.4 Gi1/0/15 auto off 0.0 n/a n/a 15.4 Gi1/0/16 auto on 6.4 IP Phone 8945 2 15.4 Gi1/0/17 auto on 6.4 IP Phone 8945 2 15.4 Gi1/0/18 auto off 0.0 n/a n/a 15.4 Gi1/0/19 auto on 13.0 IP Phone 8831 3 15.4 Gi1/0/20 auto on 6.4 IP Phone 8945 2 15.4 Gi1/0/21 auto off 0.0 n/a n/a 15.4 Gi1/0/22 auto off 0.0 n/a n/a 15.4 Gi1/0/23 auto off 0.0 n/a n/a 15.4 Gi1/0/24 auto off 0.0 n/a n/a 15.4 Gi1/0/25 auto off 0.0 n/a n/a 15.4 Gi1/0/26 auto off 0.0 n/a n/a 15.4 Gi1/0/27 auto off 0.0 n/a n/a 15.4 Gi1/0/28 auto off 0.0 n/a n/a 15.4 Gi1/0/29 auto off 0.0 n/a n/a 15.4 Gi1/0/30 auto off 0.0 n/a n/a 15.4 Gi1/0/31 auto off 0.0 n/a n/a 15.4 Gi1/0/32 auto off 0.0 n/a n/a 15.4 Gi1/0/33 auto off 0.0 n/a n/a 15.4 Gi1/0/34 auto off 0.0 n/a n/a 15.4 Gi1/0/35 auto off 0.0 n/a n/a 15.4 Gi1/0/36 auto off 0.0 n/a n/a 15.4 Gi1/0/37 auto off 0.0 n/a n/a 15.4 Gi1/0/38 auto off 0.0 n/a n/a 15.4 Gi1/0/39 auto off 0.0 n/a n/a 15.4 Gi1/0/40 auto off 0.0 n/a n/a 15.4 Gi1/0/41 auto off 0.0 n/a n/a 15.4 Gi1/0/42 auto on 3.3 IP Phone 7821 1 15.4 Gi1/0/43 auto off 0.0 n/a n/a 15.4 Gi1/0/44 auto on 6.4 IP Phone 8945 2 15.4 Gi1/0/45 auto off 0.0 n/a n/a 15.4 Gi1/0/46 auto off 0.0 n/a n/a 15.4 Gi1/0/47 auto off 0.0 n/a n/a 15.4 Gi1/0/48 auto off 0.0 n/a n/a 15.4 switch# sh post Stored system POST messages: Switch 1 --------- POST: CPU MIC register Tests : Begin POST: CPU MIC register Tests : End, Status Passed POST: PortASIC Memory Tests : Begin POST: PortASIC Memory Tests : End, Status Passed POST: CPU MIC PortASIC interface Loopback Tests : Begin POST: CPU MIC PortASIC interface Loopback Tests : End, Status Passed POST: PortASIC RingLoopback Tests : Begin POST: PortASIC RingLoopback Tests : End, Status Passed POST: PortASIC CAM Subsystem Tests : Begin POST: PortASIC CAM Subsystem Tests : End, Status Passed POST: PortASIC Stack Port Loopback Tests : Begin POST: PortASIC Stack Port Loopback Tests : End, Status Passed POST: PortASIC Port Loopback Tests : Begin POST: PortASIC Port Loopback Tests : End, Status Passed
... View more
Created by
Natalie Ramirez
in Switching
in Switching
09-22-2015
02:39 PM
09-22-2015
02:39 PM
I have a 48 port 3750 POE switch, POE works fine on ports 6, 13, 16, 17, 19, 20, 30, 42, 44. However, no other port will provide POE. If I move a cable from port 6 and plug it into port 5, no errors on switch, no power to phone. If I move it back to port 6, powers up exactly like it should. Configuration on all 48 ports is exactly the same. I have tried "power inline" "never", "auto", and "static", makes no difference. I had to go port to port to find all the good POE ports, plug in, wait 10 seconds, move to next port. Switch model number WS-C3750G-48PS-S Running IOS version 12.2.25 SEB4 Is there a factory defect issue with POE on some 3750s?
... View more
Labels:
Created by
Natalie Ramirez
in IP Telephony and Phones
in IP Telephony and Phones
05-19-2015
11:19 AM
05-19-2015
11:19 AM
Router running IOS 15.2.4 M6 c3900-universalk9-mz.SPA.152-4.M6.bin of 300+ phones 3 are registered to the SRST Cube router. #show voice register all Active registrations : 3 Total SIP phones registered: 3 Total Registration Statistics The phones show unregistered in CUCM, and the web page for each phone shows the CM ip address of the router as active. If I manually go to each phone and reset it, it will register with the CUCM. Is there a way to do it from the router they are registered on... Without rebooting the router. I tried resetting the voice register pool, as described here: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/command/reference/cme_cr/cme_r1ht.html (config)#voice register pool 10 (config-register-pool)#reset It does not acknowledge the reset command, or the restart command. Tried through call-manager-fallback, as described here: http://www.cisco.com/c/en/us/td/docs/ios/12_2/12_2x/12_2xb/feature/guide/fallback.html#wp1078946 (config)#call-manager-fallback (config-cm-fallback)#reset all Reset-All: no active phones All DNs in DOWN state It says there are no active phones. How can a reset the 3 phones that are registered on this router?
... View more
Labels:
07-25-2014
06:45 AM
Before I posted this discussion, I searched and found another post where someone recommended that. I tried that first and it didn't work, but It was where I got the idea to just try every setting on that page one at a time. So that solution technically led me to a solution that worked.
... View more
07-24-2014
03:06 PM
Found the fix: Device --> Device Settings --> SIP Profile Then went line by line, changing each and every option, saving it, resetting it, then dialing long distance. At the bottom, the checkbox that says: Early Offer support for voice and video calls (insert MTP if needed) I checked this, saved it, reset it, and dialed again. I got the long distance dial code, called my Cell phone, and got ring-back. I do not even know what that means, just know that it works. I had to create a copy of the "Standard SIP Profile" and assign it to my SIP trunk before testing. Thanks for taking the time to look at my post.
... View more
Created by
Natalie Ramirez
in IP Telephony and Phones
in IP Telephony and Phones
07-24-2014
12:31 PM
07-24-2014
12:31 PM
I have a Nortel phone system and we are evaluating CUCM. We setup a SIP trunk from the CUCM to the Nortel which is connected to a PRI, and I can dial local calls, but when I call my Cell phone, my cell rings, but all I hear is silence on my Cisco phone until I answer the cell, then it is a regular conversation. However, when I call a POTS line, I get ring-back and everything works fine. Call connects either way, with ring-back or without, it connects. When I dial long distance, the Nortel system is supposed to present me with a tone to indicate that I need to enter my long distance dialing code, I never hear the tone. I tried entering the code without hearing it, but that did nothing, eventually the call times out and I get a busy signal. Cisco IP phone -- CUCM -- Nortel -- PRI -- PSTN All of the above works with no issue with a CME. Long distance tone comes across, get ring-back on all calls, no issues. Cisco IP phone -- CME -- Nortel -- PRI -- PSTN So to make everything equal, I added a router to the mix. Cisco IP phone -- CME -- Cisco SIP router -- Nortel -- PRI -- PSTN Cisco IP phone -- CUCM -- Cisco SIP router -- Nortel -- PRI -- PSTN Still, CME everything works fine, I get ring-back on all calls and tone ready for long distance code. I ran a debug for "debug voice ccapi inout" on the Cisco SIP router, I see the source/destination from CME and from CUCM all look correct. I ran a debug for "debug ccsip messages" on the Cisco SIP router. Messages are identical right up until the part of the debug on a successful call that says: Jul 21 18:59:10.249: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg: Sent: SIP/2.0 180 Ringing On the calls that do not get ring-back, this message never appears. What is different about a CME sip trunk and how can I make a CUCM SIP trunk be the same as a CME SIP trunk? on CME pointing to Cisco SIP router: dial-peer voice 34 voip description Test1 destination-pattern 9..........$ voice-class codec 1 session protocol sipv2 session target ipv4:x.x.x.x dtmf-relay sip-notify no vad How can I make the CUCM SIP trunk do everything just like the CME that works fine above? On Cisco SIP router, pointing to Nortel: dial-peer voice 24 voip description outbound test destination-pattern 9..........$ voice-class codec 1 session protocol sipv2 session target ipv4:x.x.x.x dtmf-relay rtp-nte no vad Cisco SIP router receiving calls from both CUCM and CME: dial-peer voice 1 voip description incoming test voice-class codec 1 session protocol sipv2 incoming called-number . dtmf-relay sip-notify no vad
... View more
Labels:
Created by
Natalie Ramirez
in IP Telephony and Phones
in IP Telephony and Phones
07-17-2014
07:52 AM
07-17-2014
07:52 AM
Well, it has been 2 years since this was posted. Is there a way to turn off "auto transmit video" from the server?
... View more
Created by
Natalie Ramirez
in IP Telephony and Phones
in IP Telephony and Phones
05-23-2014
11:40 AM
05-23-2014
11:40 AM
My users... Keep on dialing 9911, then hanging up because it was an accident. Then emergency services call back and get main automated attendant, then they dispatch out to the office pissed off. 3 times this month now... Can I put a 1 second delay on the 911 dial peer so that if someone dials 9911, and realizes their mistake, they can hang up and no harm/no foul. In the off chance that it is a real emergency, the 1 second delay is not going to hurt anyone, but it will give the user that second to change his/her mind and hang up without further irritating emergency services.
... View more
- Tags:
- CME dial-peer delay
Labels:
Created by
Natalie Ramirez
in Application Networking
in Application Networking
04-21-2014
09:02 AM
04-21-2014
09:02 AM
It just occurred to me that you may need to update your optimization policies because of how different the defaults are when you go from 4.x to 5.x, they added 40 or so polices, including Citrix. "Device Groups > AllWAASGroup > Configure > Acceleration > Optimization Policies " document any special configurations you have made, and do a "Restore default", in 4.x, I had 4 special configuration policies I had created, I removed all of them and only have 1 since upgrading to 5.x because 5.x didn't have the same issues. You may also want to go to: "Device Groups > AllWAASGroup > Device Group Home " and do a "Restore default optomization policies" and "Force group settings"
... View more
Created by
Natalie Ramirez
in Application Networking
in Application Networking
04-21-2014
08:19 AM
04-21-2014
08:19 AM
It has been along time, but I seem to remember having an issue with my Optimization policies when I went from 4.4.7 - 5.0.x My fix for it was to do a fresh install from CD to my CM and get the updated default Optimization policies which were considerably different from the policies that I had been upgrading with since 4.1.x. The most important difference was in the "Class-default" policy at the very bottom which does " TFO with DRE Adaptive and LZ " which was different from the default in 4.1 which I seem to recall being TFO Only. I only have 15 WAAS in production, so changing them to a new CM was not very painful. The Class-default change made a HUGE difference in WAN performance. Device Groups > AllWAASGroup > Configure > Acceleration > Optimization Policies So, that having been said, have you tried: Device Groups > AllWAASGroup > Device Group Home Then from the menu at the top "AllWAASGroup"--> Assign devices Attempt to assign it to the devices from there with the "assign all WAEs" button.
... View more
Created by
Natalie Ramirez
in Application Networking
in Application Networking
04-21-2014
07:23 AM
04-21-2014
07:23 AM
WAAS versions greater than 5.0 all handle Citrix ICA with no configuration necessary, it is simply plug and play. WAAS does not turn off compression, it removes the Citrix compression and uses its own compression that is better on your WAN, then puts the Citrix compression back on at the other end. The client sees the packet exactly as it was sent from the Citrix server, with Citrix compression. WAAS is transparent to your users. My WAAS system is currently claiming a 27% reduction in bandwidth for Citrix. Other acceleration is much more impressive, like file copying (CIFS), web traffic, replication traffic, and SQL, all of which consistently show 70%-95% reduction in bandwidth. All of which are also plug and play with WAAS.
... View more
10-19-2015
I also just tried creating access list 701 access-list 701 deny
0000.0000.0000 ffff.ffff.ffffbut whe...
10-19-2015
I created an extended access list and allowed a single mac address in a
conference room, so only the...
09-23-2015
switch# sh loggSyslog logging: enabled (0 messages dropped, 1 messages
rate-limited, 0 flushes, 0 ov...
09-23-2015
switch#sh pow inlModule Available Used Remaining (Watts) (Watts)
(Watts)------ --------- -------- --...
09-22-2015
I have a 48 port 3750 POE switch, POE works fine on ports 6, 13, 16, 17,
19, 20, 30, 42, 44. However...
Created by
Natalie Ramirez
in IP Telephony and Phones
05-19-2015
05-19-2015
Router running IOS 15.2.4 M6c3900-universalk9-mz.SPA.152-4.M6.bin of
300+ phones 3 are registered to...
07-25-2014
Before I posted this discussion, I searched and found another post where
someone recommended that. I...
07-24-2014
Found the fix:Device --> Device Settings --> SIP ProfileThen went line
by line, changing each and ev...
07-24-2014
I have a Nortel phone system and we are evaluating CUCM. We setup a SIP
trunk from the CUCM to the N...
07-17-2014
Well, it has been 2 years since this was posted. Is there a way to turn
off "auto transmit video" fr...
Created by
Natalie Ramirez
in Unified Communications Infrastructure
06-26-2014
06-26-2014
Also, putting the CTI RP of the UCCX trigger into a partition made it
stop receiving calls from the ...
Created by
Natalie Ramirez
in Unified Communications Infrastructure
06-26-2014
06-26-2014
I tried both, both had the same result. It tells me to wait, then plays
hold music, never rings or c...
Created by
Natalie Ramirez
in Unified Communications Infrastructure
06-25-2014
06-25-2014
Thanks for the response. I saw your post and immediately thought you
were onto something. The Direct...
Created by
Natalie Ramirez
in Unified Communications Infrastructure
06-25-2014
06-25-2014
So on CUCM 9.1.2 I have a CTI route point for calls that come in on the
main number 1000 and it goes...
Public Statistics
| Date Registered | 01-19-2012 12:32 PM |
| Date Last Visited | 08-18-2017 06:43 PM |
| Total Messages Posted | 90 |
| Total Helpful Votes Received | 9 |
.jpg "Hall of Fame Cisco Employee"){kind=icon}
