Application Networking

Cisco ACE 4700 with an IPS integration

Hi, I am new to this matter and would like to have some questions answered that i am not able to find on the Cisco website. We are planning to deploy a Application Controle Engine - ACE family - and need to close the gap related to OWASP threat list...

Resolved! Question regarding NAT and directed-mode

Hello,I have two WAE 574 devices and a CM 274 all running code level 4.3.1.6, The CM is behind a PIX firewall. There is no firewall between the branch and core WAE. The branch device is behind a NAT router. The CM and SSL ASA rea behind a PIX 515 fir...

WAAS CM log - Server shutting down, exitCode=104

The CM is showing a critical alarm cms_offline_state and the log shows many lines of the following:%WAAS-DISK-2-200033: Problem trying to open device to clear partition table on [disk00] (device /dev/sda): No such device or addressand then the last...

Cisco CSS OpenSSL

Hi All I woundering if someone would be able to help with the following, is it possible to see which version of the OpenSSL is in each version of the CSS code:Either by a doc or show command:I am trying to look into the issue CVE-2011-4109, is there ...

HTTP metadatacache is not improving

HelloI have been running benchmark tests on HTTP applications with metadatacaching feature turned on. I'm running version 4.4.1 in our lab. I have the WAN setup for 1.5Mbps with 250ms of latency. The cold cache is the same response time as the warm c...

IP Nat with WCCP

Can we use the “ ip nat inside” and “ ip redirect in” statements on same interface ? I came know that we can’t use both statements on same interface, instead of this we need to move NAT statement to the outside interface or moving the ip redirect sta...

Resolved! Insert https x-forwarded-for

Hello all,I have an ACE 4700 and It is balancing a web aplication using tcp ports 80 (http) and 443 (https). The configuration of ACE is in One-Arm, it means that the ACE does a NAT to client IP source address.For requeriment legal the web aplication...

Resolved! ACE Direct Server Return documentation

Hi to all..can anyone provide me a clear guide or link to understand ho to configure a LB in Direct Server Return mode? I was looking on the web but I did not find anything able to explain a basic configuration clearly. Thanks!!!!

Resolved! ACE bridged mode query

Hi.I've typically deployed contexts in one-armed mode and used source NAT to route traffic back to the ACE from a server farm. This has worked well, however I have an application requirement to use the source IP address of the client to identify who...

Resolved! Two Service-policy on same interface same direction.

Hey Guys,I need confirmation before making some changes on ACE. I am going apply two service-policy on same interface in same direction.Actually the traffic comes over the interface is being used for management as well. So say i want to apply followi...

Cisco GSS Load Balance on multiple ports

I have a server with 2 ip address assigned to it. The first has the application running on the normal http port 80 and on the second ip address the same application is running on port 100.Is there a way to setup the GSS so that when some one hits ap...

Why can Riverbed optimize encrypted mapi and Cisco can't?

Why can Riverbed optimize encrypted mapi and Cisco WAAS can't? Is this something that is in the works and if so when is it going to available. I know you can use Outlook Anywhere, but our Systems department doesn't want to switch.Any info appreciat...

ACE filter by url

Hi,I want to redirect some url on a specific server of mywebfarm. The loadbalancing work but the specific rules I create based on http url not. (The loadbalancing dont keep the same server during the same user session by the way)Here is my config :ac...

Resolved! CSS11506 - Slot 0 to Slot 1 copy

Currently using a CSS1506 for our reverse proxy SSL.I have a couple of questions1 - Does the 11506 use an internal disk as well as the one in slot 0 ? 2 - I have a spare mem card in slot1, how can I copy all of the required boot files etc to slot 1 i...

Resolved! How do you configure One arm load balancing with source nat only applied to a specific policy?

We have a pair of load balancers located at our datacentre configured in one arm mode. The existing configuration has no nat on the inbound client (load balancing) vlan. As it stands, all the other real servers are on vlans trunked across to our cor...

Application Networking

Forum Posts

Cisco ACE 4700 with an IPS integration

Resolved! Question regarding NAT and directed-mode

WAAS CM log - Server shutting down, exitCode=104

Cisco CSS OpenSSL

HTTP metadatacache is not improving

IP Nat with WCCP

Resolved! Insert https x-forwarded-for

Resolved! ACE Direct Server Return documentation

Resolved! ACE bridged mode query

Resolved! Two Service-policy on same interface same direction.

Cisco GSS Load Balance on multiple ports

Why can Riverbed optimize encrypted mapi and Cisco can't?

ACE filter by url

Resolved! CSS11506 - Slot 0 to Slot 1 copy

Resolved! How do you configure One arm load balancing with source nat only applied to a specific policy?

ECCN, HTS/EU Taric & COO codes for products

VxLAN EVPN Multisite behavior for extended Vlans

DNAC node clusters on different subnets

WAE choses wrong loopback when building its IGP.

software-defined networks and software-defined data centers

C9350-24T

ECCN code

HTS & ECCN Code

Replace A9K-24X10GE-1G-TR

ITD for servers LB on the same vlan