Buy or Renew
Buy or Renew

Application Networking

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Cisco UCS X-Series Energy Efficiency Offer

 

Forum Posts

Start a conversation

Resolved! How to create client/server VLANs after FWSM towards ACE Module

Hi, In the concerned design, the client/server vlans are on the inside of the FWSM. So for e.g. FWSM inside is VLAN100 which receives client hits which also has the servers connected. I believe a different vlan needs to be created for the client and ...

WAAS: DRE on a 'short' link

Hi,We need to compress traffic on a short (2 msec) fat (100Mbps) link between two sites. We are not concerned with applications' chattiness - just bandwidth. Would DRE optimisation kick in for such a short link? I assume 7341 and 7371 do this in RA m...

d.gabo by • Visitor
  • 784 Views
  • 2 replies
  • 0 Helpful votes

Skype on WAAS and FWSM problem

The customer network has two kind of situations, behind the FWSM or not.Skype already normally operated under these two kind of network construction.When WAAS disposition,behind FWSM's client to use skype , it has very heavy detention even connection...

ivan_tung by • Community Member
  • 942 Views
  • 3 replies
  • 0 Helpful votes

Resolved! WAAS - WCCP L2-redirection in WS-C6509-E

Hi,I have a costumer with three offices, one is the data center. The other two offices get information from the data center and between them. Each one of these remotes offices go through two different SP to the data center, and each one is received i...

p.maciasc by • Community Member
  • 2847 Views
  • 5 replies
  • 0 Helpful votes

Resolved! show flows on CSS

Hi,I am using source group on my CSS to nat server initiated traffic to VIP address.Currently it does not work, so I am doing troubleshooting.I am using ISA1-NAT service for source group.configure!*************************** GLOBAL ******************...

Resolved! Ace Sticky Configuration

Hi Guys,I'm trying to set up a sticky configuration on an ACE modeule in a 6500.I've got the loadbalancing woking happily but need to ammend the config to add stickiness.As far as I know the first command is someting on the lines of...sticky http-coo...

Packet with source IP 0.0.0.0

Hi,is possible that a css11503, configured as http and https load balancer, sends packet with source IP 0.0.0.0?!With an IDS, I can see packet with source IP 0.0.0.0, coming from the load balancer, but I cannot understand why.Can someone help me?!Bes...

csiracusa by • Level 2
  • 645 Views
  • 1 replies
  • 0 Helpful votes

Resolved! AutoCAD 2007 No Benefits update?

I have a customer who is looking at WAAS specifically for AutoCAD 2007. There is plenty of press about the application and how it re-writes the entire file upon each save action. This will clearly cause the WAE to repeat Cold transfers every time, vi...

todd.martin by • Community Member
  • 832 Views
  • 1 replies
  • 0 Helpful votes

IOS SLB - Vserver always UP

Hi guys.. i have this situation with IOS SLB. Theres a virtual server and 2 real servers. The traffit to be balanced runs in a UDP port. We are using a basic ping probe to monitor the real servers. The thing is that even if the probes fails, the Vser...

Load more
Top Solution Authors
View All

Review Cisco Networking for a $25 gift card