our customer reported free memory shrinking.who can help, because my experiense with css devices is very poor. here are some details:thanks for your helpmichael
our customer reported free memory shrinking.who can help, because my experiense with css devices is very poor. here are some details:thanks for your helpmichael
Hi,Is there a WAAS command that will allow me to clear a TCP connection thats been hung for 500+ hours? The WAE is running 4.0.13.b23.Thanks,Mike
I'm a newbie to configuring an ACE module so bear with me. I'm trying to create a VIP that answers to port 80 that NAT's and loadshares that to a serverfarm on port 7778.My relevant config statements:probe http v01_http_probe port 7778 interval 30 ...
Hello , We have Cisco 4500 that running WCCP with Cisco Cache (WAE-512.Microsoft SMS (using port 80) not working when the traffic pass through. Because 4500 not support redirection with ACL we can't exclude the SMS traffic.( Exclude in the cache not ...
Hello All,We've just deployed a scenario with CM/Core in our Main office and Edge in remote office. We're using DMPVN between offices with lowered MTU/MSS over the tunnels (1400/1360 respectively). The traffic itself between the offices works just fi...
I have configured an LDAP probe using the script provided. It is stuck in INIT state saying that No. Internal error: is incrementing. I have tried script LDAP_PROBE DEBUG but I don't know how to view the debug output. I have logging up and running an...
i want to make ethernet channel btween wae in data center & datacenter switch ,wae has two giga port and i use transperant wccp interseption is that possible as i need bandwidth more than 100MB btween wae & switch another Q did any one tested port s...
Is there any possobility of problem if LAN side of inline group is set to 1Gb but WAN side is only 100 Mbps ? Also I can not see LAN and WAN settings in WAE-512K9 of 4.0.13 although this is clearly shown in 4.0.7 configuration of of 511.How would I ...
I have a point to point site with redundant links load sharing. I've installed a WAAS appliance on each end. We also have a Packetshaper installed on each end with shaping turned off. The setup is client -WAAS-Packetshaper-Router- Circuit-Router-PAck...
I put a couple web servers behind the ACE and it appears to work. But I cannot get to the internet. I'm assuming I need to enable NAT on the ACE and I read the SCE Security Guide. If I enable NAT on ACE for my outgoing traffic, will it impact the num...
Hi,I'm trying to answer a question while doing design. I am planning on deploying a CSM in bridge mode with multiple vlans. I need to create a serverfarm which has real servers in two separate server side vlans.I would then present the Vserver on t...
Forgive me if someone has asked this before - though I couldn't see anything relevant on a forum search.I have CSS box-to-box redundancy working fine. The servers we are load balancing have x2 adapters which are teamed with a cable to each CSS.If one...
Hi,The ACE permits to allocate finely ACE resource for each context.We can check the context resource usage by the command "sh resource usage".The Denied outputs gives details regarding the "Number of denied resources because of oversubscription or r...
When I try to enter the member [resource_class] command under the context config mode I get...Error: resources in useAny idea how I get around this?Note: I am trying to do this so that I can configure stickiness in my context and I getError: sticky r...
ip route 0.0.0.0 0.0.0.0 [6509-int-vlan11]ip route 1.1.8.0 255.255.255.0 [6509-int-vlan10]ip route 1.1.7.0 255.255.255.0 [6509-int-vlan10]Route Summary for Context C1 (RouteId 1)Route Source Count Memory (bytes)----------------------------...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
03-06-2024 12:27 PM | ||
02-21-2024 04:21 AM | ||
10-04-2022 06:16 AM | ||
09-26-2022 11:58 AM | ||
09-13-2022 02:40 AM |