Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Sorry as this is a general question.What are the applications that can be load web applications. Can I use ibalanced using the CSS other than t for mail servers or any other type of servers.Please helpThank you RegardSanjith
Hi,We have a situation where servers needs to be loadbalanced on same vlan and from different vlan as well.We have figured out that from different vlan is simple to setup and works. Also we figured out that we need to do source NAT - 'nat client'usin...
Hi allI have a question on IOS SLB on the 6500. The 6500 in question is not functioning as a layer 3 device at the moment and the only l3 interface configured on it is for management.Given this fact ,can IOS SLB be configured on this 6500 or does bot...
Can I configure the CSS 11501 to serve content from Web Server A until it becomes unavailable and then serve content from Web Server B? I don't want access to hit the 'B' box until 'A' is unresponsive.I do not want the content web servers load balanc...
Can anybody provide me with samples of configuration to load-balance SMTP & LDAP servers with CSS ? I feer having the same problem as with FTP when the session is initiated from the server side and that we have to make some special adds-on to the con...
I have a client using an SSL cert to connect to an ftp server. The user is being redirected to a CE-511 via WCCP v2 but the FTP connection does not work. If I bypass the user (in my wccp acl) it works fine - following a default route to my PIX.Any in...
How do I stop an A record being up for a domain, when there is a redirect rule associated to that domain that does not go down when all other services are down.i'm using a kal-ap-vip keepalive on the A record.service redirect_ets keepalive type none ...
Good day!Often in log of my CSS 11503 is appeared next error messages:APR 3 23:18:05 1/1 113661 FLOWMGR-6: FM_ReTransTimeout: Re-Transmit timeout ERRORAPR 3 23:18:05 1/1 113662 FLOWMGR-6: FM_Tcp: Handling generic FMTCP flowRe-Transmit ERRORAPR 3 23:1...
Hi, we want to put a new 'logo_home.gif' on the main page of our GSS (this is the logo of the two heads). We want to put a 'banner' here instead.However, I cannot see this file in the GSS directory ? Does anyone know if this is accesable or not ?chee...
Hi all,I get the following output when issuing a 'show memory' command on the GSS. total freeMemory 1003 MB 792 MB total used free Mem: 1003 756 246 How/Why does the GSS give different values for used/free memory ? Is there two different 1Gb memory c...
Hello,my question is about getting access to the LocalDirector 430 through the console port: I thought it was just a regular rollover cable (with pins 1 through 8 reversed), but for some reason, that doesn´t seem to work. I know that there is a Cisco...
Hello, we have deployed IOS SLB on Cisco 7206VXR (NPE-G1) running 12.3.14T.An IPIP Tunnel is terminated on the 7206 router. We discovered that packets arriving through this tunnel i/f are not handled by the SLB and are being rejected (causing connect...
Hi,I would like to set the "maxconns" parameter on the named real server TESTREAL, belonging to the serverfarm TESTFARM. Could someone give me the corresponding XML code to be sent in a POST request ?Thank you,Yves
Hi, I am looking at deploying a pair of CS11503 (probably in ASR redundancy mode) connected to redundant 6509 data center aggregation switches. I am also considering a pair of AVS 3120 accelerator appliances. Is it best to have each AVS 3120 directly...
