Application Networking

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco UCS X-Series Energy Efficiency Offer

 

Forum Posts

I'm looking to see if I can get the DTD for the CSS 115xx Image XML parser. I'd like to be able to parse and validate my XML configuraiton files prior to attempting to load them. Are these published on CCO anywhere, or can I download them from the s...

wiwells by Level 1
  • 425 Views
  • 1 replies
  • 0 Helpful votes

Dear All,I have here in my company 25 Cisco Switch 3560 .as i know, i will configure the Switch with the Basic configuration like Hostname & IP-Address - & Gateway.My 2 question is :-1- if i configure the switch with the Basic Configuration like IP-A...

I'm thinking about using the probefacility in CSM to probe almost all servers, including normally notloadbalanced servers, because then I have the possibility to send users to a sorryserver when something is wrong. Questin: How many probes can I run ...

mruuth by Level 1
  • 540 Views
  • 3 replies
  • 0 Helpful votes

Hi,my customer experiences strange delay variantions from accessing the webserver directly instead of accessing the servers via the CSS.the CSS is configured for cookiestickiness with the string commands.The difference in delay is as following:Access...

jfoerster by Level 4
  • 680 Views
  • 2 replies
  • 0 Helpful votes

Hi,I have 2 x (cisco 6509/sup720/CSM).I try to setup vlan with FT setup:r1:module ContentSwitchingModule 7 ft group 1 vlan 9 priority 30 preempt vlan A server ip address 10.0.99.2 255.255.0.0r2:module ContentSwitchingModule 7 ft group 1 vlan 9...

HiWe have cisco CSS CSS11050 running on 5.00 Build 45, I have a pretty simple and stragight forward configuration.I have two server sitting in a server farm, our QA users are the process of the testing, when the start the load with more than 50 users...

rbatchu by Level 1
  • 541 Views
  • 1 replies
  • 0 Helpful votes

I have a CSS11506 with an SSL module loaded. The CSS is gigabit trunked to an L2 switch.Load balancing the web servers, running on port 80, is working fine with standard HTTP. Once enabling SSL on the CSS and trying to access the service via HTTPS, t...

nadhem by Level 1
  • 799 Views
  • 3 replies
  • 0 Helpful votes

HI,is it possible to monitor the CPU of a CSS 1150x.I did not find any hint about this in the docs. I tried to figure out if it is pssoible via the HSE but was not able to find a way.If gatherig the CPU-Utilization is not possible how to detect if a ...

jfoerster by Level 4
  • 887 Views
  • 5 replies
  • 0 Helpful votes

First time SSL newbie question.I am trying to get a certificate installed on an SSL Mod. using the cut and paste method. I generated a key pair, configured the trustpoint, generated a certificate request and pasted it into verisigns site. The reply I...

carlsond by Level 1
  • 965 Views
  • 6 replies
  • 0 Helpful votes

Is anyone else using HSE to manage their CSS devices?We have HSE 1.9 and I am having trouble when I change a css configuration on the CSS CLI. The HSE does not seem to pick up the change. I have to remove the device from the discovery list and add it...

Is there any way to configure an HTTP health probe that will test a web page and fail if it takes too long for the server to respond. I have attempted to do this (see below) but the "receive" parameter doesn't seem to help. We are currently having a ...