Good Morning,I was asked to upgrade the Cisco ISR1131 with the latest recommended versions. I had no issues with the router: I downloaded the IOS and followed the standard procedure for Cisco routers. However, regarding the integrated EWC, I’m not su...
Forum Posts
Hi, I am trying to make Cisco ISE HA. On the Cisco site, I did not find a user manual for it.I have cloned the main ISE 3.1.0 and changed the IP.I am trying to make HA:Administration > Deployment > Register (FQDN, user, password)But I have this error...
I've using EVE-NG but would like to know what is a good alternative to 9000v and 8000v image since its resource heavy image and I can't run multiple.Also so far only found 9000v to allow <switchport mode trunk> command directly whereas IOSV L2 switch...
I've noticed a difference in the way the command needs to be typed in Cisco Packet Tracer vs Cisco CML. In Cisco Packet Tracer (Version 8.2.1.0118), the command has to be typed like this: crypto key generate rsa general-keys modulus 2048. In Cisco CM...
I wanted to see if I can get anyone's assistance with the enrichment data pulled into a new SN ticket from Cisco Catalyst.I’ve created a few test incidents where I’m using a CI that is currently experiencing an Issue in Cisco. However, when I enter ...
Hello,We have a NCS540 which we do not know the user pass to login. Is there a way to by pass the configured user pass as in ciso IOS? If not what is the procedure to reset the user pass thank you,
hello communitylately after upgrading my ISR 4331 router IOS this syslog message appear and cause the router to reload%SPA_OIR-3-SW_INIT_TIMEOUT: subslot 0/5: SPA initialization not completed-Traceback= 1#b29b2857b4051a30c665fc71d8fa5182 :55D4BEEA300...
In the above topology iosvl2-3 is the STP root bridge and it sends BPDUs out of G1/1 on the Po1 etherchannel group (LACP). When I simulate an outage on g1/2 everything continues fine. However, because the BPDUs are exiting out of Po1 member g1/1, i...
Resolved! where is the Activity grader?
Hi, Could anyone tell where is the Activity Grader for Packet Tracer? Thanks Victor
Hi all,I am using cisco ISE 3.1 Patch 6. I am looking to upgrade patch version. please kindly recommend which new patch released is the best one? 7,8,9?Best regardThea
I'm stuck in rommon. I do a bootflash:cat9k_iosxe.17.15.01.spa.bin and it attempts to boot the image then I get this error " ERROR: failed to boot from bootflash:cat9k_iosxe.17.15.01.spa.bin (Out of Resources)" . What are my options to get this imag...
Resolved! Unable to import lab into CML
I'm unable to import a lab into CML. I tried importing two YAML files, but both gave errors, as shown in the screenshot. I'm using the hosted version of CML on Cisco DevNet, and the error points to "nxosv9000." Do you think this issue could be due to...
Resolved! Upgrade of cisco 9200 failing
I tftped a firmware file(cat9k_lite_iosxe.17.12.04.SPA.bin) to a cisco 9200 switch and when I run the install add file flash:cat9k_lite_iosxe.17.12.04.SPA.bin activate commitI get the following errorError: Failed to install_add_activate_commit packag...
Hello, I have searched far and wide for any drivers to be able to read a Catalyst 3500 XL from 2003 from my Linux laptop, using a USB to RJ45 console cable. I need to be able to manage VLANs, manage ports, and do some other things for my SoHo network...
Hello, Could anyone please help me?We encountered this issue where when our DX80s call a non-Webex meeting platform, the DX80s will trying calling the SIP URI for 1 minute, and if no one answers, the DX80s won't join the call after that 1 minute of t...
