08-01-2012 05:41 AM - edited 03-14-2019 10:17 AM
Hello,
We have an issue here very strange: we have a cluster of UCCX 8.5 and every time we need to change the roles between them some agents cannot login anymore, they receive the typical error message:
"Login failed due to a configuration error. Please ask your system administrator to associate your phone with the RM JTAPI Provider user ID according to the instructions in the administrators guide"
However, the phone is associated perfectly because they were working fine before. As a workaround, we have discovered that if I dissasociate the phone with this user, exit from the user, enter again and re-associate it, in general it will work again.
Until now I was doing that but recently it is happening to more users and this is becoming unmanageable, does anybdoy have this problem as well? any suggestions, please?
Thanks in advance.
08-01-2012 06:00 AM
Hi Dsalamanca,
Please de-associate all the Agent Phones MAC addresses from the RmCm Application user in CUCM, and again Reassociate all of them one more time.
After this, please perform the DIrectory Resync operation from the UCCX Desktop Administrator.
This will solve this issue.
Thanks,
Anand
Please rate helpful posts !!
09-14-2012 09:18 AM
Have been having the same issue. Completely removing the accounts from UCCX and waiting long hours for replication to occur and then re-adding them has solved the problem in 3 cases. The above is so much faster. Here's the spoonfeed:
Hope this helps!!
Now if I can only get my tech accounts to stop blinking out and disappearing for 30 seconds, and then reappearing, we'd be golden...
-Heather
09-14-2012 09:23 AM
Hi,
Yes for quicker resync you can either open the Resources pages from the UCCX admin or perfrom CDA resync operation.
Hope this helps.
Anand
Pls rate helpful posts !!
03-19-2013 02:59 AM
Hello, I solved it only de-associating the phones that were no longer in use by agents, and it never has shown the error again. Maybe one of those phones was bringing problems to the servers.
Unfortunately this comment is not a great help for people having the same issue but it worked for me.
05-23-2016 12:03 PM
You just won the internet today! Thank you so much for posting these instructions. It worked like a charm for us.
-OB1
03-19-2013 03:29 AM
Hi,
what exact version of UCCX 8.5 you have. you hitting the following bug
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtq37975
you need to update to UCCX 8.5 SU2 or above. If you have AQM I recommend to upgrade to SU3 or above
HTH
Anas
please rate if it is helpful
03-19-2013 03:52 AM
Hello Anas,
Thank you for the information, we have 8.5(1)SU2 installed, however I don't see this bug as resolved in the resolved caveats, (neither on the SU3 or SU4 release notes) are you sure it's fixed on SU2? I think it is solved in a later SW version according to the bug information, Cisco says it's solved from 8.5(1.12024.1) which seems to be higher than SU4... Am I wrong?
Nowadays we are not experiencing this issue anymore, but it's good to know about this bug... Another customer is also experiencing it with an UCCX 7. I will post how we solve it.
Regards,
DS
07-29-2016 02:40 PM
I had the same problem when i changed one user´s IP Phone. The solution was:
- Associate the new phone and desassociate the old one on rmcm user
- Go to CCX » Subsystems » Data Synchronization » Select CCG/Triggers/CM Telephony Users » Data Resync
I hope it helps!!!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide