11-14-2016 08:30 AM - edited 03-14-2019 04:46 PM
Hello All,
I had a lot of search regarding this issue ... but when moving from CAD to Finesse , You have to re-add all Not-Ready and Wrap-up codes .
is there a way of exporting those codes ? .. even from the CLI .. ? DB ?? ..
Thanks A lot,
Ahmed Salah
Solved! Go to Solution.
11-17-2016 02:30 AM
Ahmed, If you will look in the UCCX 10.6 Design Guide, it talks about CAD to Finesse Migration utility tool but once you click on the link, the tool does not seem to exist any more. Refer below:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/crs/express_10_6/design/guide/UCCX_BK_CBB99111_00_cisco-unified-contact-center-express/UCCX_BK_CBB99111_00_cisco-unified-contact-center-express_appendix_0111.html#UCCX_RF_F672AC20_00
However, you can still post your question at the below forum to have a confirmation on this whether the tool exists or not
https://communities.cisco.com/community/developer/finesse
Regards
Deepak
11-16-2016 03:23 PM
Hello All,
Appreciate if any one has any recommendation ..
Even to insert those as bulk inside Finesse is not valid option ! ..
11-17-2016 02:30 AM
Ahmed, If you will look in the UCCX 10.6 Design Guide, it talks about CAD to Finesse Migration utility tool but once you click on the link, the tool does not seem to exist any more. Refer below:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/crs/express_10_6/design/guide/UCCX_BK_CBB99111_00_cisco-unified-contact-center-express/UCCX_BK_CBB99111_00_cisco-unified-contact-center-express_appendix_0111.html#UCCX_RF_F672AC20_00
However, you can still post your question at the below forum to have a confirmation on this whether the tool exists or not
https://communities.cisco.com/community/developer/finesse
Regards
Deepak
11-17-2016 07:25 AM
https://developer.cisco.com/site/finesse/docs/tools/cad-to-finesse-migration-tool/
11-17-2016 11:10 AM
Thanks a lot Deepak,
I was able to find the tool , but it is stating that it can work from UCCX 9.x ..
anyway , i will try it on a snapshot .. may be it can help ..
i will let you know if it works ..
Thanks A lot,
Ahmed Salah
11-18-2016 12:26 PM
Hello Deepak,
I tested the tool , and it worked !!! .. everything is not migrated to the Finesse DB ..
this is just awesome !!
it is stating that i must have access to both servers , while the UCCX 11 is in Isolated network , i did it as follows :
- On the production network with UCCX 8.5 , launched the tool , and "export"
- After the tool finished its magic , I then copied the folder with everything to the isolated network ..
- Run the tool again , but then "import" .. and voila .. it is done ..
Thanks A lot,
Ahmed Salah
11-19-2016 04:28 AM
Good to hear that Ahmed and glad that it worked for you and made the migration job a little easier. Thanks for marking the Correct Answer as well.
Regards
Deepak
11-17-2016 07:26 AM
Ahmed,
See my reply below.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide