Buy or Renew
Buy or Renew

Controllers

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Developer Sustainability Week Events

Build for Better Code Challenge

Cisco U. Spotlight Registration


>> View previously featured conversations <<

Forum Posts

Start a conversation

Resolved! APIC-EM Sandbox Credentials changed?

Hi,I can't seem to be able to access the APIC-EM sandbox Login - APIC - Enterprise Module anynore with the following credential;username = "admin"password = "C!sc0123"Can someone confirm if the credentials have been changed and if yes what are the ne...

fabrice75 by • Level 1
  • 1826 Views
  • 1 replies
  • 0 Helpful votes

APIC-EM in the cloud

I'm looking at doing a POC of APIC-EM. Are there any cloud service providers that I can run APIC-EM on to connect back to my physical gear or VIRL?Any recommendations on setting up a POC?

awilki012 by • Level 1
  • 1919 Views
  • 3 replies
  • 0 Helpful votes

APIC-EM Hub/Spoke

Hi Experts,I'm new to APIC-EM and would like clear up few confusing point that I'm not able to understand from the documentation.After deploying the APIC-EM in ESXi, I access the controller from management IP, then I install CSR1000v in ESXi which is...

usrana by • Cisco Employee
  • 1290 Views
  • 2 replies
  • 0 Helpful votes

Resolved! APIC-EM Grapevine behind NAT

I have a copy of APIC-EM 1.1.2 in a dev environment. There is a NAT device protecting the environment. I can log into the Grapevine console through the use of a static NAT to 14141 I get the console but no content. Just "error retrieving task informa...

twgraham by • Level 1
  • 2510 Views
  • 4 replies
  • 0 Helpful votes

Resolved! APIC-EM EFT2 ACL API

Hi everyone,I have noticed that the EFT2 version is no longer available on DevNet, and a new GA release is out. But I can't seem to find the Policy Analysis support previously available on EFT2 in the GA +1. I was highly reliant on the ACL-related AP...

Resolved! Problem with Path Trace

Hello,I have problem with path trace, in one direction it can discover path of the flow and in another it can't. Problem is always in the same interface of the switch.What could be wrong with the configuration of the switch or path trace?Thank you in...

dgombovic by • Level 1
  • 2933 Views
  • 7 replies
  • 1 Helpful votes

Resolved! How to create routing policy?

Hello,I would like to create routing policy that will route all IP phone traffic to one specific router. Every try in which I use categories or pathPreference results with error code "BadRequest" so I have few questions:-is there any API documentatio...

dgombovic by • Level 1
  • 4630 Views
  • 7 replies
  • 1 Helpful votes

IP Device Tracking

I have configured APIC-EM in stand alone mode and have discovered a majority of my network devices. On many of these devices, I am unable to view host information within the APIC console. Port information is gathered successfully. I have verified tha...

TID_Orion by • Level 1
  • 9337 Views
  • 19 replies
  • 0 Helpful votes

Resolved! APIC-EM credentials changed

The credentials listed here  https://devnetsandbox.cisco.com/RM/Diagram/Index/2e0f9525-5f46-4f46-973e-0f0c1bf934fa?diagramType=Topologydon't appear to be working on the always  on sandbox.Please post the new credentials.Is there a mail list I should ...

randajon by • Cisco Employee
  • 1779 Views
  • 1 replies
  • 0 Helpful votes

Resolved! APIC-EM discovery using AD/RADIUS credentials

I installed APIC-EM and was trying to run device discovery.  We use Active Directory RADIUS for auth so for user name I have to enter: domain\user. APIC-EM interface complains that I am using an illegal char \.  I have tried it using '\' and "\", als...

vantipov by • Level 1
  • 2113 Views
  • 5 replies
  • 1 Helpful votes
Load more