Heads Up :
The post you are writing will appear in a public forum. Please ensure all content is appropriate for public consumption. Review the employee guidelines for the community here.
Leave details in the post, such as the name of the sandbox and details about the problem. Make sure to add a label with the type of problem you are having (such as Connectivity Issues and VPN, Sandbox Reservation Issues, Sandbox Specific Technical Issues, or Other Sandbox Issues).
If you are new to our development labs, you can develop, code & configure for free with the DevNet Sandboxes today.
Cisco ACI Simulator nodes are showing as inactive and some time not registered from last 1 day. Can you guys look on this. We are not able to practice.
I reserved a spot to test out the new CML and I clicked on the URL that was sent to me:Lab Network Address: devnetsandbox-usw1-reservation.cisco.com:20154But it failed "Anyconnect was not able to establish a connection to the specified secure gateway...
When upgrading memory from 8GB to 32GB on the node resources flavors tab vmanage boots up asking which disk to use: Available storage devices:hda 20GBhda1 3GBhda2 16GBhdd 0GB1) hdd Please advise as vManage is not starting up properly.
I created a Lab in CML DevNet and I exported it. The next day I reserved another lab and I tried to import my Yaml lab I created the day before. The file was imported and I try to start the routers and they show they are started, but when I try to co...
First time I have tried this but I believe I should be able to ‘virl up’ one of the topologies listed in the ‘virl search’ output using For example ‘virl up virlflies/genie_learning_lab’. This fails with a repo not found error. I have tried this on b...
Hi, I am on Aci kubernete integration lab, ansible playbook doesnt install kubernetes component, yu can see error message below, doing what it says in error didnt help, i could not be able to start kubelet servise even installing them manuely, /var...
Trying to Connect to Cisco SD-wan Lab with VPN information received in email. I do have internet access.Lab Network Address: devnetsandbox-emea-gwy.cisco.com:20193When using AnyConnect to login, I get below message"Connection attempt has timed out. P...
Good morning,
I reserved the NSO Lab this morning and it Active (with errors) but I can't find what the errors are...
I started the lab and the obvious happened, there are two devices that are not reachable (dist-sw01 and dist-sw02).
Is it fixable or...
I am unable to login to the Meraki Dashboard through the Meraki Always On Sandbox. Here is the process I go through and the error messages I get: I first login to the devnetsandbox.cisco.com website using my Cisco account. I then scroll down to the...
C:\>ssh developer@ios-xe-mgmt.cisco.com -p 8181ssh: connect to host ios-xe-mgmt.cisco.com port 8181: Connection timed out Is there something wrong with this csr1000v ? -Aaron
Hi, We are unable to do Finesse agent login. Can you please help with this. Attached screenshot. Error:This Finesse Server is currently out of service. For more information, contact your administrator. Cisco VPN details : Lab Network Address: devne...
Hello,
So I have finally managed to get access to the DNAC Sandbox after few days, but soon as I have logged in I am met with the following:
Automation and Assurance services have been temporarily disrupted. The system is working to restore this f...
Hi, I have setup a lab, it is in active state but since half an hour didint receive an e-mail, i have recently updated my e-mail into linked account just before login to the sandbox reservation. Maybe some session hanged somewhere. I think here is ...
I can get to the DevBox in this DNA Center Hardware Sandbox 2 that I have reserved and the only other device on the network that I can ping is the WLC. I cannot get to DNA-C or anything device either by ping or http/https. Any assistance would be a...
