Edge Computing Infrastructure

Hi,I am using IR809 router with "IOx bundle image of ir800-universalk9-bundle.SPA.156-2.T1" and the Guest OS installed by default with the bundle.I am using the  SDK 1.1.0 for application development. I am following LXC Applicaton Development on Cisc...

So... there is a certain application available for 64 bit ubuntu that I'd like to attempt to run on the 829.Does this mean I need to create a yocto distro which includes some package management, like apt-get, and use ubuntu repos?Would this work?  Ha...

Hi Guys,I am trying to use a bridge group for interface gig 5 so the can obtain an ip address. The OS seems to get an ip address and I can ping it but I see this message come up once I add gig 5 to the bridge-group.000416: *Oct 17 17:41:40.580: %IOX-...

Hi,we are having a container application that runs on IR8x9 architecture. In our use case, we have lots of routers running our container in a distributed architecture. In order to give support clients on specific use-cases, we plan to use openvpn to ...

Hi,we are testing the latest firmware/GOS combination that was provided to us regarding lxc container installation:Firmware: ir800-universalk9-bundle.SSA.156-2.0.49.GBGOS: ir800-ioxvm-1.1.0.4-T.binEverything seems fine with our container software, bu...

Hi guys. I'm new to Cisco router configuration. I am in the process of configuring the IR829 router and am stuck. I am trying to follow the instructions here (https://developer.cisco.com/media/iox-dev-guide-6-23-16/platforms/platform-ir8xx/#getting-s...

While understanding that there are existing serial ports on IR829, I am wondering whether USB port can be used for serial connectivity into GOS.

Hi guys,IR 809 fails to boot properly if the USB storage is inserted during power up. Boot stucks in rommon-1> and there's no way to make it run. I tried to bootHV from the usb drive but this failed as well. If I try to dir there are some errormessag...

HiI wanted to use IOx debug commands to see why my GOS is not starting. I entered "debug iox", as shown below, and then tried to start the GOS. The GOS is not starting, as shown by the result of the "show iox host list detail" command, but nor do I s...

It seems to me that there would be a larger need for IOx based network nodes that ran on non rugged enterprise environment, like the 3560, 3850, etc. I find that there would be a large use case for creating apps living in these environments where the...

HiI would like to create my own Yocto image tor test purposes, especially with LXC containers.I can use the Yocto Quick Start and the Yocto Build Appliance.When running the build appliance, which is a menu driven system for creating images, I can cho...

My IR829 and IR809 devices did not arrive with power adaptors, so I created my own and wrote that up here:https://github.com/DevOps4Networks/IOX-Notes/tree/master/How_To_Power_UpSince then, I received two PWR-60W-AC-V2= power supples from Cisco that ...

HiThe attached configuration is an attempt to create a DHCP pool from which I can assign addresses both to the GE1-4 switch interfaces and the GOS.The outcome of applying this configuration is as expected for all aspects, except for the address assig...

HelloI am trying to measure the temperatue with TEMPer USB Thermometer, using 1 USB port on my CGR1120. This port is mapped to the GOS and device is correctly discovered with dmesg. As a next step, I have found that it can be used in Linux, using lib...

HiIn the SDK 1.0, there is a tutorials/apps/Makefile that looks like it should build all of of the apps in the same directory.In that Makefile there is a requirement for the IOX_YOCTO_PROJECT_DIR variable to be defined.That variable does not seem to ...