04-18-2018 11:17 PM - edited 03-17-2019 12:39 PM
Hi,
We are trying to setup an 8865 phone with 8865 KEM (dual screen, 14 buttons, 2 pages), however, the module does not seem to be coming up. At one stage, we received an alert stating "Accessory Added: The phone is not setup for the expansion module" however, there seems to be no backlight or any activity on the expansion module.
Phone has been setup with KEM and phone button template (10 lines + 28 BLF) in CUCM, running 12.0.1-SR1 firmware on CUCM 10.5.2. Switch is 2960X and hence is capable of 802.3at (PoE+).
Total drawn Inline power on port is 14.7 watts irrespective of having KEM connected to phone.
Is there anything else I could check? Is there anyway to check whether expansion module is receiving power? I'd assume it receives power from side USB port on phone which, by the way, is also enabled on CUCM under product specific configuration.
Any help will be appreciated.
Thanks.
04-19-2018 03:26 AM - edited 04-19-2018 03:39 AM
What kind of switch are you using? Cisco or another vendor? I ask because some non-Cisco switches do not support the LLDP negotiation for powering Phone+KEM.
04-19-2018 07:57 AM
04-19-2018 08:09 AM
And he said he had the module added on the phone configuration page and a phone button template to cover the KEM.
If you remove the KEM, does the base phone power up and register?
04-19-2018 04:47 PM
Thanks guys, it's Cisco 2960X switch, KEM is added to the phone config and phone is fully registered to CUCM and can make/receive calls.
04-19-2018 05:14 PM
04-29-2018 05:48 PM
Thanks everyone for your inputs.
Apparently, the KEM status was always shown disconnected in DEBUG mode. And it appears that the only KEM option we're getting on CUCM phone config page was 36-button module whereas the correct module should be 28 button module. So since the phone's configured with 36-button module, it wouldn't recognise 28 button module and hence complains that it's not configured.
TAC have confirmed that this issue relates to the defect documented in CSCvd77762
https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvd77762/?referring_site=bugquickviewredir
According to TAC, installing device pack 10.5(2)(16134-1) or later will resolve this.
Thanks again.
06-27-2018 05:59 AM
Hello,
i saw your post and seems that we have same issue with 8851 for audio 28 button module as it is not coming up and phone accessories showing disabled by admin.
please suggest how can resolve this as we are running cucm 11.5.x and 8851 is having 11.7 firmware..
06-27-2018 07:48 AM
06-27-2018 07:57 AM
06-27-2018 11:58 AM
06-27-2018 10:00 PM
We had the issue resolved by installing the latest device pack for CUCM 10.5.2.
06-27-2018 11:20 PM
07-08-2018 09:19 PM
08-07-2018 01:19 AM
Hi we had the firmware upgrade last wekend en have the same problem.
It si phone 8851 with extension module en power injector.
Give same problem
With firmware cterm-sip88-11-7-11 works fine.
We dit some test with lates switches with inline power en er whas no problem.
Only with power inject in when wrong.
Regards
Jan Meeling
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide