04-08-2013 04:07 PM - edited 03-16-2019 04:40 PM
Hey guys,
I'm wondering if someone can give a help on this issue.
I have a CISCO 2921 with a TDM interface E1 connecting using r2-digital to the PSTN provider.
I can receive calls successfuly but when i try to place calls i'm receving the following error:
Call Entry(Disconnect Cause=42, Voice Class Cause Code=0, Retry Count=0)
and the phones show me "High Traffic, Try again later"
My controller is configured like that:
controller E1 0/0/0
framing NO-CRC4
line-termination 75-ohm
ds0-group 1 timeslots 1-10 type r2-digital r2-compelled ani
cas-custom 1
country brazil
metering
debounce-time 10
release-ack
double-answer
category 2
answer-signal group-b 1
request-category 8
The Voice-port is configured like that:
voice-port 0/0/0:1
cptone BR
In annex there are the output from debug voice ccapi inout, debug vpm signal and the running config.
Thanks in advance for any help.
Filipe
04-08-2013 11:41 PM
Hi,
kindly check the below link for disconnect cause
http://networking.ringofsaturn.com/Routers/isdncausecodes.php
Cause No. 42 - switching equipment congestion.
This cause indicates that the switching equipment generating this cause is experiencing a period of high traffic.
What it means:
Just too much going on at this point on the ISDN network to get the call through to its destination.
did you check the provider for this case ?
HTH
Anas
please don't forget to rate the helpful posts
04-09-2013 12:18 AM
Hello
The disconnect is being thrown because we are receive an R2_stop from the e1r2 circuit , it is shown above .You have to discuss that with your service provider . I recommend to use PRI instead.
Thank you
please rate if this will help
04-09-2013 12:20 AM
Hi
please find the below configuration , i have a customer has the same issue and the below configuration solved the issue
network-clock-participate wic 0
!
voice call send-alert
!
voice service voip
qsig decode
fax protocol pass-through g711alaw
h323
h225 timeout tcp call-idle value 2
h225 timeout t302 1
h225 timeout t304 1
h225 timeout setup 1
call start slow
controller E1 0/0/0
framing NO-CRC4
ds0-group 0 timeslots 1-10 type r2-digital r2-compelled ani
ds0-group 1 timeslots 11-15,17-31 type r2-digital r2-compelled ani
cas-custom 0
country brazil
ani-digits min 4 max 20
cas-custom 1
countrybrazil use-defaults
disconnect-tone
interface GigabitEthernet0/0
description LAN Connection
ip address 10.10.10.10 255.255.255.0
duplex auto
speed auto
h323-gateway voip bind srcaddr 10.10.10.10
voice-port 0/0/0:0
cptone BR
voice-port 0/0/0:1
cptone BR
timeouts interdigit 2
timeouts call-disconnect 3
timeouts wait-release 2
dial-peer voice 1000 voip
destination-pattern 68..
session target ipv4:10.10.10.1
dtmf-relay h245-alphanumeric
codec g711ulaw
dial-peer voice 1 pots
preference 1
destination-pattern .T
direct-inward-dial
port 0/0/0:1
Thank you
please rate if this will help
04-09-2013 01:15 AM
Filipe,
I am not an expect on R2-CAS but looking at the ccapi logs I can tell that the call is disconnected from your ITSP
The disconnect is coming from the outbound call leg (109 and 110)
The questions is which side is diconnecting the call..The gateway or the Telco..When we look at the logs we can see that ots the Telco because in ccapi logs anything wit "_" is the call leg talking to CCAPI...eg cc_api_call_disconnected and anything without "_" eg ccapicalldisconnected is ccapi talking to the call leg.
So I suggest you open a case with your telco
Apr 8 23:06:49 UTC: r2_reg_channel_disconnected(0/0/0:1(1))
Apr 8 23:06:49 UTC: //110/002385FB0500/CCAPI/cc_api_call_disconnected:
Cause Value=42, Interface=0x29E96298, Call Id=110
Apr 8 23:06:49 UTC: //110/002385FB0500/CCAPI/cc_api_call_disconnected:
:
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"
06-05-2019 08:38 AM
MAYBE IT IS TOO LATE TO REPLY but it can help for other admins on the future.
I had the problem with calls to cellphone, some cellphone the problem was wiht the way to dial, some cellphone has to dial direct like your house. That was my problem, it was not problem for my router or pbx.
I attach my debug from the router it sends the legend "Cause Value= 42"
Hope it can helps u!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide