06-25-2010 09:30 PM - edited 03-15-2019 11:25 PM
Hi all
I would much appreciate if someone can help me to overcome the following issue. I have configured a Cbarge feature in CME and due to the hardware conference issue I am not able to test the feature. It is giving me the error message as “ Failed to Barge in”
I know it is a hardware conference issue, however I don’t find any mistake in the config and the hardware conference is associated successfully with CME.
Please see the detail and give me a direction as where I am making the mistake…… it is killing my time
Thanks
PVDM2 - Details
=====
Slot0:
PVDM Slot 1:
48-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 4.0
Part Number : 73-8540-05
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number :
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-48
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 ED 41 04 00 82 49 21 5C 05 42 41 30
0x10: 88 00 00 00 00 02 04 C1 8B 46 4F 43 31 30 34 34
0x20: 33 57 31 43 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 88 50 56 44 4D 32 2D 34 38 89 56 30 31 20 D9 02
0x40: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
=================Config-=================
voice-card 0
dspfarm
dsp services dspfarm
!
sccp local FastEthernet0/0.105
sccp ccm 142.105.66.254 identifier 1 priority 1 version 7.0
sccp
!
sccp ccm group 1
bind interface FastEthernet0/0.105
associate ccm 1 priority 1
associate profile 2 register myconf
associate profile 1 register mytrans
keepalive retries 5
keepalive timeout 5
!
dspfarm profile 1 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 3
associate application SCCP
!
dspfarm profile 2 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
telephony-service
sdspfarm units 2
sdspfarm transcode sessions 3
sdspfarm tag 1 mytrans
sdspfarm tag 2 myconf
conference hardware
=================================
abc#sh dsp
abc#sh dspfarm all
Dspfarm Profile Configuration
Profile ID = 1, Service = TRANSCODING, Resource ID = 1
Profile Description :
Profile Service Mode : Non Secure
Profile Admin State : UP
Profile Operation State : ACTIVE
Application : SCCP Status : ASSOCIATED
Resource Provider : FLEX_DSPRM Status : UP
Number of Resource Configured : 3
Number of Resource Available : 3
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30
Codec : g711alaw, Maximum Packetization Period : 30
Codec : g729ar8, Maximum Packetization Period : 60
Codec : g729abr8, Maximum Packetization Period : 60
Dspfarm Profile Configuration
Profile ID = 2, Service = CONFERENCING, Resource ID = 2
Profile Description :
Profile Service Mode : Non Secure
Profile Admin State : UP
Profile Operation State : ACTIVE
Application : SCCP Status : ASSOCIATED
Resource Provider : FLEX_DSPRM Status : UP
Number of Resource Configured : 2
Number of Resource Available : 2
Codec Configuration
Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required
Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required
SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED
0 5 23.8.1 UP N/A FREE xcode 1 - - -
0 5 23.8.1 UP N/A FREE xcode 1 - - -
0 5 23.8.1 UP N/A FREE xcode 1 - - -
0 7 23.8.1 UP N/A FREE conf 2 - - -
0 7 23.8.1 UP N/A FREE conf 2 - - -
Total number of DSPFARM DSP channel(s) 5
=================== Debug during Cbarge====================
debug ephone hw-conference
Jun 26 03:41:27.694: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:41:27.694: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:41:27.706: Check associated hwconf with callid 15
Jun 26 03:41:27.710: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:41:27.710: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:41:30.602: Check associated hwconf with callid 15
Jun 26 03:41:30.990: SkinnyHwconfBridgeMedia:dn = 4, chan 1, phone = 1 stream 0
Jun 26 03:41:30.990: SkinnyHwconfBridgeMedia:Call not in conference
Jun 26 03:41:31.587: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:41:31.587: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:41:33.183: SkinnyCBargeButtonPress: New adhoc conf barge
Jun 26 03:41:33.183: skinny_hwcfb_get_adhoc_number:
Jun 26 03:41:33.183: SkinnyCBargeButtonPress: New adhoc conf barge: setup failed!
Jun 26 03:41:44.523: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:41:44.559: SkinnyHwconfConfSKButtonSet:for dn 4 chan 1 set=0 conf_sk=0
===================When I try to conference =========================
un 26 03:45:08.777: SkinnyHideAdhocConfNumber for dn=2 chan=1 streamID=0
Jun 26 03:45:08.785: Check associated hwconf with callid 17
Jun 26 03:45:08.789: SkinnyHideAdhocConfNumber for dn=2 chan=1 streamID=0
Jun 26 03:45:09.869: Check associated hwconf with callid 17
Jun 26 03:45:10.253: SkinnyHwconfBridgeMedia:dn = 2, chan 1, phone = 1 stream 0
Jun 26 03:45:10.253: SkinnyHwconfBridgeMedia:Call not in conference
Jun 26 03:45:10.589: SkinnyHideAdhocConfNumber for dn=2 chan=1 streamID=0
Jun 26 03:45:11.445: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:15.857: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:15.881: SkinnyHideAdhocConfNumber for dn=3 chan=1 streamID=0
Jun 26 03:45:16.589: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:16.589: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:17.841: SkinnyHwconfBridgeMedia:dn = 3, chan 1, phone = 0 stream 0
Jun 26 03:45:17.841: SkinnyHwconfBridgeMedia:Call not in conference
Jun 26 03:45:17.889: SkinnyHwconfBridgeMedia:dn = 4, chan 1, phone = 1 stream 0
Jun 26 03:45:17.889: SkinnyHwconfBridgeMedia:Call not in conference
Jun 26 03:45:18.589: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:18.589: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:22.017: SkinnyAddDnToHwConference: phone=1 (dn=2 chan=1 state=9) (conf_dn=4 conf_chan=1 state=4)
Jun 26 03:45:22.017: SkinnyAddDnToHwConference: New adhoc conference
Jun 26 03:45:22.017: skinny_hwcfb_get_adhoc_number:
Jun 26 03:45:22.017: SkinnyAddDnToHwConference: Adhoc new conference setup failed!
Jun 26 03:45:23.817: SkinnyHideAdhocConfNumber for dn=4 chan=2 streamID=0
Jun 26 03:45:28.165: SkinnyHideAdhocConfNumber for dn=4 chan=2 streamID=0
Jun 26 03:45:28.193: SkinnyHwconfConfSKButtonSet:for dn 4 chan 2 set=0 conf_sk=0
Jun 26 03:45:30.461: SkinnyHideAdhocConfNumber for dn=2 chan=1 streamID=0
Jun 26 03:45:30.481: SkinnyHwconfConfSKButtonSet:for dn 2 chan 1 set=0 conf_sk=0
Jun 26 03:45:34.161: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:34.161: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:34.321: SkinnyHwconfBridgeMedia:dn = 4, chan 1, phone = 1 stream 0
Jun 26 03:45:34.321: SkinnyHwconfBridgeMedia:Call not in conference
Jun 26 03:45:35.277: SkinnyHideAdhocConfNumber for dn=4 chan=1 streamID=0
Jun 26 03:45:35.313: SkinnyHideAdhocConfNumber for dn=3 chan=1 streamID=0
Jun 26 03:45:35.317: SkinnyHwconfConfSKButtonSet:for dn 4 chan 1 set=0 conf_sk=0
Jun 26 03:45:35.317: SkinnyHwconfConfSKButtonSet:for dn 3 chan 1 set=0 conf_sk=0
================================================================
As trouble shooting step, I trying to add the " conference ad-hoc under the ephone-dn ( otc-lie), it is giving me error)
Abc(config-ephone-dn)#conference ad-hoc
DN 4 is tied to ephone 1 button 3
Remove dn 4 from the ephone button config
If i remove the button, I am not able to share the line with 2 phone for Cbarge
thanks for your help and time
Solved! Go to Solution.
06-26-2010 03:51 AM
Hi, you are not configuring the conference DN properly. Create the DN like below:
!
ephone-dn x octo-line
number A100
conference ad-hoc
!
ephone-dn y octo-line
number A101
conference ad-hoc
!
Never think to use any existing DN (which is used on any phone) as conference DN. Also 'number A100/A101' means it's not dialable by any user mistakenly, only system can call the DN.
HTH.
Please rate helpful posts!
06-26-2010 03:51 AM
Hi, you are not configuring the conference DN properly. Create the DN like below:
!
ephone-dn x octo-line
number A100
conference ad-hoc
!
ephone-dn y octo-line
number A101
conference ad-hoc
!
Never think to use any existing DN (which is used on any phone) as conference DN. Also 'number A100/A101' means it's not dialable by any user mistakenly, only system can call the DN.
HTH.
Please rate helpful posts!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide