08-13-2013 02:40 AM - edited 03-16-2019 06:49 PM
Hi All,
Anyone know if the below command has a SIP equivalent?
telephony-service
url idle http://XXX/idle.php idle-timeout 5
Trying to get the SIP handsets (9971) to display the same page as the SCCP phones.
08-13-2013 06:03 AM
Check under voice register global. I don't have a CME box in front of me but at least url directory exists there in the CME Admin Guide; I would expect other keywords to as well.
conf t
voice register global
url idle http://XXX/idle.php idle-timeout 5
Please remember to rate helpful responses and identify helpful or correct answers.
08-15-2013 03:49 PM
Hi Jonathan, thank you for the response. I've tried that but there's no such commands under "voice register global", nothing seemed remotely close to it.
CME(config-register-global)#?
voice register global configuration commands:
application Define application
attempted-registrations Define size of the attempted-registrations table
authenticate Define auth mode for SIP CME/SRST
bandwidth allow SIP SDP bandwidth related options
call-forward Decide call forward parameters for an SIP phone
default Set a command to its defaults
dialplan-pattern Define E.164 telephone number prefix
exit Exit from voice register global configuration mode
external-ring Set external ringing to be included into alert-info
fac Voice register global FAC setup
ip Set ip packet options
max-dn Define max number of dn
max-pool Define max number of pool
mode Define mode: CME/SRST
mwi MWI service in SRST mode
no Negate a command or set its defaults
outbound-proxy Configure an Outbound Proxy Server
overlap-signal Configure Overlap Signaling support
service Service configuration in voice reg global
system Define system message
timeouts Define timeout value for sip phone
timezone Set timezone for SIP Phones
I have tried putting it under "telephony-service" but being a SIP phone it didn't pick it up there.
I'm ok if it's not supported under CME but just wanted some confirmation.
08-15-2013 04:45 PM
Michael,
This guide- http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/command/reference/cme_u1ht.html#wp1016489
shows that some CME versions have a URL command under voice register global but it doesn't seem that it there is idle URL in any CME version for SIP.
It may just be one of the things that applies from telephony service. Did you try regenerating the CNF Files afterwards?
Brian
08-17-2013 04:33 AM
Hi Brian, sorry previous output I didn't fully enable SIP. URL command does exist and after drilling deeper into the command there doesn't seemed to be anything related to idle URL.
I did regenerate CNF Files and SIP profiles after enabling it under "telephony service", I rebooted the handsets too but they don't seemed to acknowledge "url idle".
The php script is dedinately valid, I tried enabling it under the "service url" button and the 9971 would correctly load the page after pressing the service button.
CME(config-register-global)#?
voice register global configuration commands:
application Define application
apply-config apply config for the 99/89 phones, restart all other sip phones
attempted-registrations Define size of the attempted-registrations table
authenticate Define auth mode for SIP CME/SRST
bandwidth allow SIP SDP bandwidth related options
bulk Define a pattern for bulk registration
call-feature-uri Define TNP SIP phone's Call Feature URI
call-forward Decide call forward parameters for an SIP phone
camera Enable camera
conference Configure conference type for adhoc
create Create profile for SIP phone
date-format Set date format for IP Phone display
default Set a command to its defaults
dialplan-pattern Define E.164 telephone number prefix
dst Enable / define daylight saving time
exit Exit from voice register global configuration mode
external-ring Set external ringing to be included into alert-info
fac Voice register global FAC setup
file Enable generation of the text profile
forwarding Decide if forwarding local is enabled for SIP phone
hold-alert Enable On-Hold alert for SIP phone
ip Set ip packet options
load Select the firmware load file
logo Define logo url that will be used by SIP phone
max-dn Define max number of dn
max-pool Define max number of pool
mode Define mode: CME/SRST
mwi Generate stutter tone for SIP mwi
network-locale Define network locale
no Negate a command or set its defaults
ntp-server Define NTP server address for TNP phones
olsontimezone Set olson timezone for IP Phones
outbound-proxy Configure an Outbound Proxy Server
overlap-signal Configure Overlap Signaling support
phone-redirect-limit Define max number of redirect per call for SIP phone
privacy Enable privacy for SIP shared-line phone
privacy-on-hold Enable privacy-on-hold for SIP shared-line phone
reset Reset all SIP phones
restart restart all SIP phone
service Service configuration in voice reg global
source-address Define IP address and port for SIP CME
tftp-path Define tftp path for SIP CME
time-format Set time format for IP Phone display
timeouts Define timeout value for sip phone
timezone Set timezone for SIP Phones
upgrade Generate OS79XX.TXT for firmware upgrade
url Define SIP phone URL's
user-locale Define SIP Phone user locale
video Enable video
voicemail Set the voicemail access number called when the messages button is pressed
CME(config-register-global)#url ?
authentication authentication url
directory directory url
service service url
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide