05-10-2011 04:15 AM - edited 03-16-2019 04:53 AM
Hi,
I have just been provided a new voice line by provider. I have put an initial config on the e1 controller card and once i got the Channel group configured I put a config on the serial interface. i am a little unsure of how to progress the config at this point. config is below for each interface.
interface Serial0/0/0:1
description Link To Eircom
bandwidth inherit
ip address 172.21.70.254 255.255.255.0
encapsulation frame-relay
#sh controller e1
E1 0/0/0 is up.
Applique type is Channelized E1 - balanced
Cablelength is Unknown
Description: Eircom Circuit
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20080918, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
Data in current interval (684 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
1 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 34 Unavail Secs
Total Data (last 24 hours)
22596 Line Code Violations, 44 Path Code Violations,
2 Slip Secs, 0 Fr Loss Secs, 1 Line Err Secs, 0 Degraded Mins,
2 Errored Secs, 0 Bursty Err Secs, 1 Severely Err Secs, 1468 Unavail Secs
while the serial interface protocol was showing up its now showing down
E#sh ip interface brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 unassigned YES NVRAM up up
GigabitEthernet0/0.1 192.168.16.254 YES NVRAM up up
GigabitEthernet0/0.10 172.21.60.254 YES NVRAM up up
Service-Engine0/0 172.31.60.1 YES TFTP up up
GigabitEthernet0/1 unassigned YES NVRAM administratively down down
Serial0/0/0:1 172.21.70.254 YES manual up down
BRI0/3/0 unassigned YES NVRAM up up
BRI0/3/0:1 unassigned YES unset down down
BRI0/3/0:2 unassigned YES unset down down
BRI0/3/1 unassigned YES NVRAM up up
BRI0/3/1:1 unassigned YES unset down down
BRI0/3/1:2 unassigned YES unset down down
Loopback0 172.31.60.1 YES NVRAM up up
Paul.
Solved! Go to Solution.
05-10-2011 09:30 AM
What is the T1 fractionalized into? Is there a data ciruit on some channels along with the PRI? What channels, specifically, are for which?
05-10-2011 04:27 AM
A voice line and you configure as if it was frame-relay ???
If recommend you engage a reputable consultant for further support.
05-10-2011 09:30 AM
What is the T1 fractionalized into? Is there a data ciruit on some channels along with the PRI? What channels, specifically, are for which?
05-11-2011 02:19 AM
Hi Guy's,
thanks for your suggestions here. I have managed to get this one resolved and below is the configuration applied to the card. hope this helps somebody else.
Assuming this is just an E1 card (and not a T1/E1 card), you'll need to do a few things:
voice service voip
fax protocol cisco
h323
h225 display-ie ccm-compatible
!
!
Controller e1 0/0/0
Pri-group timeslots 1-XX - XX being the number of available lines
Interface Serial 0/0/0:15
isdn supp-service name calling
no isdn outgoing display-ie
!
Then your dial-peers
Dial-peer voice X pots - X being the dial peer number you assign
Destination-pattern 9T
Incoming called .
Port 0/0/0:15
!
voice-port 0/0/0:15
connection plar 6001
Applying this configuration brought my card up.
Thanks again,
Paul.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide