cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
581
Views
0
Helpful
3
Replies

CUBE HA Can't enter redundancy-group 1 under voice service voip

VON CLAWSON
Level 3
Level 3

I'm configuring CUBE HA on 4461 routers. Smart licensing is enabled and authorized. Cube status is showing good

 

PHC-COLO-ISR-02#sh cube status
CUBE-Version : 12.7.0
SW-Version : 16.12.3, Platform ISR4461/K9
HA-Type : none
Licensed-Capacity : 400
Calls blocked (Smart Licensing Not Configured) : 0
Calls blocked (Smart Licensing Eval Expired) : 0

 

voice service voip
mode border-element license capacity 400
allow-connections sip to sip
no supplementary-service sip refer
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
no fax-relay sg3-to-g3
sip
session refresh
options-ping 60
midcall-signaling passthru
g729 annexb-all
sip-profiles inbound
sip-profiles 101
sip-profiles 100 inbound
no call service stop

 

redundancy
mode none
application redundancy
group 1
name CUBE-HA
priority 100 failover threshold 75
timers delay 30 reload 60
control Port-channel2 protocol 1
data Port-channel2
track 1 shutdown
track 2 shutdown
protocol 1
name Provider_RG
timers hellotime 4 holdtime 12
protocol 2
name Internal_RG
timers hellotime 4 holdtime 12

 

But when I try to enter the redundancy-group 1 under the voice service voip configuration I get this

 

PHC-COLO-ISR-02(conf-voi-serv)#redundancy-group 1
^
% Invalid input detected at '^' marker.

 

Here is my licenses 

 

License Usage
==============

ISR_4400_UnifiedCommunication (ISR_4400_UnifiedCommunication):
Description: Unified Communications License for Cisco ISR 4400 Series
Count: 1
Version: 1.0
Status: AUTHORIZED
Export status: NOT RESTRICTED

ISR_4400_Security (ISR_4400_Security):
Description: Security License for Cisco ISR 4400 Series
Count: 1
Version: 1.0
Status: AUTHORIZED
Export status: NOT RESTRICTED

ISR_4400_Hsec (ISR_4400_Hsec):
Description: U.S. Export Restriction Compliance license for 4400 series
Count: 1
Version: 1.0
Status: AUTHORIZED
Export status: RESTRICTED - ALLOWED
Feature Name: hseck9
Feature Description: Export Controlled Feature hseck9

 

CUBE v12 Trunk Standard Session (CUBE_T_STD):
Description: Cisco Unified Border Element (CUBE) Trunk Standard Session
License
Count: 400
Version: 1.0
Status: OUT OF COMPLIANCE
Export status: NOT RESTRICTED

 

Please rate if this helps.
3 Replies 3

Not sure if it’s related, but you’re not licensed for redundant trunk sessions.

“CUBE v12 Trunk Standard Session (CUBE_T_STD):
Description: Cisco Unified Border Element (CUBE) Trunk Standard Session”

You’ll need to have CUBE_T_RED for HA.



Response Signature


Yes, I knew that part. But will that stop me from being able to put in that command? Or is this a bug in this IOS?

Please rate if this helps.

Your guess is as good as mine. To really know you have a few options, a couple of them are listed below, there are likely others as well.

  • Upgrade or downgrade to another version to test your theory of a defect in your specific version
  • Open a SR with TAC to work with them to find out the cause of your problem

 



Response Signature


Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: