03-07-2013 12:38 AM - edited 03-16-2019 04:07 PM
Dear All
i am planning to upgrade our Call Manager from Version
8.6.2.21900-5 to CUCM 9.X below is my hardware detail. i would like to know it is possible to upgrade by using same hardware as below
admin:show version active
Active Master Version: 8.6.2.21900-5
Active Version Installed Software Options:
cmterm-bfcp-e.8-6-2.cop
ciscocm.refresh_upgrade_v1.1.cop
cmterm-android-12.cop
admin:show hardware
HW Platform : 7835H2
Processors : 1
Type : Family: Xeon
CPU Speed : 2333
Memory : 6144 MBytes
Object ID : 1.3.6.1.4.1.9.1.584
OS Version : UCOS 5.0.0.0-2
Serial Number :
RAID Version :
RAID Firmware Version: 7.22
RAID BIOS Version: N/A
BIOS Information :
10/25/2010
RAID Details :
Smart Array P400 in Slot 1
Bus Interface: PCI
Slot: 1
Serial Number: PAFGK0P9VWY1Z5
Cache Serial Number: PA82C0J9VWY19R
RAID 6 (ADG) Status: Enabled
RAID 6 (ADG) Enabler Status: Enabled
Controller Status: OK
Chassis Slot:
Hardware Revision: Rev E
Firmware Version: 7.22
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 15 sec
Cache Board Present: True
Cache Status: OK
Accelerator Ratio: 50% Read / 50% Write
Total Cache Size: 256 MB
Battery Pack Count: 1
Battery Status: OK
SATA NCQ Supported: True
Array: A
Interface Type: SAS
Unused Space: 0 MB
Status: OK
Logical Drive: 1
Size: 136.7 GB
Fault Tolerance: RAID 1+0
Heads: 255
Sectors Per Track: 32
Cylinders: 35132
Stripe Size: 64 KB
Status: OK
Array Accelerator: Enabled
Unique Identifier: 600508B100105039565759315A350001
Disk Name: /dev/cciss/c0d0
Mount Points: /partB 24.5 GB, / 24.5 GB, /grub 258 MB, /common 85.4 GB
physicaldrive 1:1
Port: 2I
Box: 1
Bay: 1
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD6
Serial Number: BS05P8B0NNDP0848
Model: HP DG146BABCF
physicaldrive 1:2
Port: 2I
Box: 1
Bay: 2
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 10000
Firmware Revision: HPD6
Serial Number: BS05P8B0NNDM0848
Model: HP DG146BABCF
Solved! Go to Solution.
03-07-2013 01:19 AM
MCS-7835-H2 is only supported for bridge upgrade...
Here is the hardware requirements..
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"
03-07-2013 01:19 AM
MCS-7835-H2 is only supported for bridge upgrade...
Here is the hardware requirements..
Please rate all useful posts
"opportunity is a haughty goddess who waste no time with those who are unprepared"
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: