Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
1865
Views
10
Helpful
9
Replies

E1 PRI integration using QSIG

luiz.alexandre.paiva
Level 1
Level 1

‎03-01-2007 10:17 AM - edited ‎03-14-2019 08:17 PM

Does anybody has a sample config of how to interconnec an E1 PRI at 2801 to an E1 PRI at one PBX Hicom 300 using QSIG? This implementation will be done at Brazil.

Labels:
0 Helpful
9 Replies 9

t.silva
Level 1
Level 1

‎03-01-2007 10:28 AM

It's a example:

controller E1 0/0

pri-group timeslots 1-31

interface Serial0/0:15

no ip address

no logging event link-status

isdn switch-type primary-qsig

isdn incoming-voice voice

isdn bchan-number-order ascending

no cdp enable

0 Helpful

paolo bevilacqua
Hall of Fame
Hall of Fame

‎03-01-2007 10:33 AM

There are just two settings that are general and mandatory, one is "switch-type qsig", either network or user side, and the other is under "voice service voip", "qsig decode" to pass name display. All the rest must be configured locally depending on what exactly are you doing.

There are numerous config examples that you can search here with the keywords hicom 300, qsig, etc...

0 Helpful

Steffen.Baier
Level 1
Level 1
In response to paolo bevilacqua

‎03-05-2007 04:44 AM

What Ecma Version are you going to be using ?

Ecma1 or EcmaV2 as the ISDN BChannel Command depends on this one.

I am on a course this week but I post my config as I spend numerous hours getting it right. Last hurdle for me is now the connected number as this shows at present only my 5 digit extension.

Steff

0 Helpful

luiz.alexandre.paiva
Level 1
Level 1
In response to Steffen.Baier

‎03-05-2007 06:06 AM

Hi Steff,

We are using ECMA1.

And who is supporting you, Cisco or a Partner?

Tks,

Alex

0 Helpful

Steffen.Baier
Level 1
Level 1
In response to luiz.alexandre.paiva

‎03-06-2007 08:51 AM

I dig this info out tonight as I am just on a CCNA Boot Camp.

I work for an Cisco Partner

I did not get any real support of cisco but I used to work for siemens so knowledge of both systems came handy.

Speak soon

0 Helpful

Steffen.Baier
Level 1
Level 1

‎03-06-2007 02:14 PM

OK,

as pomised ! I can only recommend EcmaV2 Qsig and then you must use the isdn contiguous-bchan or any call hitting B-Channel 15 to 30 will not work.

We had the following issues with Call Manager 4.2 (3) via our 37xx Routers on EcmaV1:

Calls from CCM to any Hicom and hitting a CFNA were only able to speak for 6 seconds then got disconnected.

Calls from Hicom to CCM with a CFB got busy and not another extension or VM

No Names being transmitted etc. and a lot of other issues.

Here are the general Hicom settings but you will need to adopt them to your config !

We use fully International Numbering plan and I have changed the numbers ;-)

LRTG, KNNR, LBER, KNNR, depend on the location

Important is the LDPLN in connction with the LODR

Allgemein

to reach LDN

90 is the Bund to the provider( IPC or CISCO )

6 is rollover PSTN

within LDAT is a seperation between DEE / SPR optional ( is not really needed!!! )

Important:LODR

44 is being send first and TON is internat !!

ADD-LDPLN:0-W-00-44-207-12-5-X,0&1&2&3&4&5&6&7&9,814&814&814&814&814&814&814&815&814,3,;

/// ADD-LDAT:LROUTE=814,LSVC=VCE,LVAL=1,TGRP=90,ODR=1054,LAUTH=8,CARRIER=2,ZONE=EMPTY,LATTR=NONE,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=814,LSVC=VCE,LVAL=1,TGRP=6,ODR=1054,LAUTH=1,CARRIER=3,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-6,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=814,LSVC=DTE,LVAL=1,TGRP=90,ODR=1054,LAUTH=8,CARRIER=1,ZONE=EMPTY,LATTR=NONE,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=814,LSVC=DTE,LVAL=1,TGRP=6,ODR=1054,LAUTH=1,CARRIER=3,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-6,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=815,LSVC=VCE,LVAL=1,TGRP=90,ODR=1054,LAUTH=8,CARRIER=2,ZONE=EMPTY,LATTR=NONE,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=815,LSVC=VCE,LVAL=1,TGRP=6,ODR=1054,LAUTH=1,CARRIER=3,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-6,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=815,LSVC=VCE,LVAL=1,TGRP=1,ODR=1054,LAUTH=1,CARRIER=2,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-2,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-RICHT:MODE=LRTENEW,LRTE=814,LSVC=VCE,NAME="PSTN ",TGRP=1&90&6,DNNO=1-0-0,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,ROUTATT=NO,EMCYRTT="",INFO=NEUTRAL;

/// ADD-RICHT:MODE=LRTEEXT,LRTE=814,LSVC=DTE,TGRP=1&6&90;

/// ADD-RICHT:MODE=LRTENEW,LRTE=815,LSVC=VCE,NAME="PSTN ",TGRP=1&90&6,DNNO=1-0-0,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,ROUTATT=NO,EMCYRTT="",INFO=NEUTRAL;

ADD-LODR:ODR=1054,CMD=ECHO,FIELD=4;

ADD-LODR:ODR=1054,CMD=ECHOALL;

ADD-LODR:ODR=1054,CMD=NPI,NPI=ISDN,TON=INTERNAT;

ADD-LODR:ODR=1054,CMD=END;

0 Helpful

Steffen.Baier
Level 1
Level 1
In response to Steffen.Baier

‎03-06-2007 02:15 PM

97769 is a code to get to our office in the uk via a shortdial

ADD-LDPLN:97769-X,0&1&2&3&4&5&6&7&8&9,811&811&811&811&811&811&811&812&812&811,1,;

/// ADD-LDAT:LROUTE=811,LSVC=ALL,LVAL=1,TGRP=90,ODR=812,LAUTH=8,CARRIER=2,ZONE=EMPTY,LATTR=NONE,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=811,LSVC=ALL,LVAL=1,TGRP=6,ODR=812,LAUTH=1,CARRIER=3,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-6,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=812,LSVC=ALL,LVAL=1,TGRP=90,ODR=812,LAUTH=8,CARRIER=1,ZONE=EMPTY,LATTR=NONE,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-RICHT:MODE=LRTENEW,LRTE=811,LSVC=ALL,NAME="CN-QSIG ",TGRP=1&90&6,DNNO=1-0-0,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,ROUTATT=NO,EMCYRTT="",INFO=NEUTRAL;

/// ADD-RICHT:MODE=LRTENEW,LRTE=812,LSVC=ALL,NAME="CN-QSIG ",TGRP=90,DNNO=1-0-0,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,ROUTATT=NO,EMCYRTT="",INFO=NEUTRAL;

ADD-LODR:ODR=812,CMD=OUTPULSE,DGTS=4420747;

ADD-LODR:ODR=812,CMD=ECHO,FIELD=2;

ADD-LODR:ODR=812,CMD=NPI,NPI=ISDN,TON=INTERNAT;

ADD-LODR:ODR=812,CMD=END;

Attentand Console:

Via the network we use 442071291 were 91 is the Number of the AC

PSTN is 442071234568

ADD-LDPLN:0-W-00-44-207-1234568,0&1&2&3&4&5&6&7&9,816&816&816&816&816&816&816&810&816,3,;

/// ADD-LDAT:LROUTE=816,LSVC=VCE,LVAL=1,TGRP=90,ODR=810,LAUTH=8,CARRIER=1,ZONE=EMPTY,LATTR=NONE,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=816,LSVC=VCE,LVAL=1,TGRP=6,ODR=1054,LAUTH=1,CARRIER=3,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-6,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=816,LSVC=VCE,LVAL=1,TGRP=1,ODR=1054,LAUTH=1,CARRIER=2,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-2,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=816,LSVC=DTE,LVAL=1,TGRP=6,ODR=1054,LAUTH=1,CARRIER=3,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-6,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=816,LSVC=DTE,LVAL=1,TGRP=1,ODR=1054,LAUTH=1,CARRIER=2,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-2,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=810,LSVC=VCE,LVAL=1,TGRP=90,ODR=810,LAUTH=8,CARRIER=2,ZONE=EMPTY,LATTR=NONE,DNNO=1-0-0,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-RICHT:MODE=LRTENEW,LRTE=816,LSVC=VCE,NAME="PSTN ",TGRP=1&90&18&6,DNNO=1-0-0,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,ROUTATT=NO,EMCYRTT="",INFO=NEUTRAL;

/// ADD-RICHT:MODE=LRTEEXT,LRTE=816,LSVC=DTE,TGRP=1&6;

/// ADD-RICHT:MODE=LRTENEW,LRTE=810,LSVC=VCE,NAME="PSTN ",TGRP=90,DNNO=1-0-0,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,ROUTATT=NO,EMCYRTT="",INFO=NEUTRAL;

ADD-LODR:ODR=810,CMD=OUTPULSE,DGTS=442071291;

ADD-LODR:ODR=810,CMD=NPI,NPI=ISDN,TON=INTERNAT;

ADD-LODR:ODR=810,CMD=END;

ADD-LODR:ODR=1054,CMD=ECHO,FIELD=4;

ADD-LODR:ODR=1054,CMD=ECHOALL;

ADD-LODR:ODR=1054,CMD=NPI,NPI=ISDN,TON=INTERNAT;

ADD-LODR:ODR=1054,CMD=END;

ADD-LDPLN:97769-91,0&1&2&3&4&5&6&7&8&9,813&813&813&813&813&813&813&812&812&813,1,;

/// ADD-LDAT:LROUTE=813,LSVC=ALL,LVAL=1,TGRP=90,ODR=814,LAUTH=8,CARRIER=1,ZONE=EMPTY,LATTR=NONE,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=813,LSVC=ALL,LVAL=1,TGRP=6,ODR=814,LAUTH=1,CARRIER=3,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-6,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=813,LSVC=ALL,LVAL=1,TGRP=1,ODR=814,LAUTH=1,CARRIER=2,ZONE=EMPTY,LATTR=WCHREG,DNNO=2-3-2,VCCYC=KEINE,CBMATTR=1,SCCID=4;

/// ADD-LDAT:LROUTE=812,LSVC=ALL,LVAL=1,TGRP=90,ODR=812,LAUTH=8,CARRIER=1,ZONE=EMPTY,LATTR=NONE,VCCYC=KEINE,CBMATTR=1,SCCID=4;

ADD-LODR:ODR=814,CMD=OUTPULSE,DGTS=442071234568;

ADD-LODR:ODR=814,CMD=NPI,NPI=ISDN,TON=INTERNAT;

ADD-LODR:ODR=814,CMD=END;

ADD-LODR:ODR=812,CMD=OUTPULSE,DGTS=4420747;

ADD-LODR:ODR=812,CMD=ECHO,FIELD=2;

ADD-LODR:ODR=812,CMD=NPI,NPI=ISDN,TON=INTERNAT;

ADD-LODR:ODR=812,CMD=END;

0 Helpful

Steffen.Baier
Level 1
Level 1

‎03-06-2007 02:15 PM

To reach the German Attendand Console you dial the 0 at the end

Important :LODR

49 is being send first and TON is internat !!

ADD-LDPLN:0-W-123-0,0&1&2&3&4&5&6&7&8&9,219&219&219&219&219&219&219&218&218&219,,3,,,,NEIN;

/// ADD-LDAT:LROUTE=219,LSVC=VCE,LVAL=1,TGRP=90,ODR=1033,LAUTH=8,CARRIER=4,ZONE=EMPTY,LATTR=NONE,VCCYC=4;

/// ADD-LDAT:LROUTE=219,LSVC=VCE,LVAL=1,TGRP=1,ODR=1033,LAUTH=8,CARRIER=4,ZONE=EMPTY,LATTR=NONE,VCCYC=4;

/// ADD-LDAT:LROUTE=219,LSVC=DTE,LVAL=1,TGRP=1,ODR=1033,LAUTH=1,CARRIER=7,ZONE=EMPTY,LATTR=WCHREG,DNNO=8-5-701,VCCYC=4;

/// ADD-LDAT:LROUTE=218,LSVC=VCE,LVAL=1,TGRP=1,ODR=1033,LAUTH=1,CARRIER=7,ZONE=EMPTY,LATTR=WCHREG,VCCYC=4;

/// ADD-LDAT:LROUTE=218,LSVC=DTE,LVAL=1,TGRP=1,ODR=1033,LAUTH=1,CARRIER=7,ZONE=EMPTY,LATTR=WCHREG,VCCYC=4;

/// ADD-RICHT:MODE=LRTENEW,LRTE=219,LSVC=VCE,NAME="",TGRP=90&1,DNNO=8-5-100,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,PLB=NO,ROUTATT=NO,EMCYRTT=NO,INFO="",PDNNO=0,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO;

/// ADD-RICHT:MODE=LRTEEXT,LRTE=219,LSVC=DTE,TGRP=1;

/// ADD-RICHT:MODE=LRTENEW,LRTE=218,LSVC=VCE,NAME="",TGRP=1,DNNO=8-5-701,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,PLB=NO,ROUTATT=NO,EMCYRTT=NO,INFO="",PDNNO=0,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO;

ADD-RICHT:MODE=LRTEEXT,LRTE=218,LSVC=DTE,TGRP=1;

ADD-LODR:ODR=1033,CMD=OUTPULSE,DGTS=49691230;

ADD-LODR:ODR=1033,CMD=NPI,NPI=ISDN,TON=INTERNAT;

ADD-LODR:ODR=1033,CMD=END;

ADD-LDPLN:0-W-713-1-X,0&1&2&3&4&5&6&7&9,217&217&217&217&217&217&217&218&217,,3,,,,NEIN;

ADD-LDPLN:0-W-713-2-X,0&1&2&3&4&5&6&7&9,217&217&217&217&217&217&217&218&217,,3,,,,NEIN;

ADD-LDPLN:0-W-713-6-X,0&1&2&3&4&5&6&7&9,217&217&217&217&217&217&217&218&217,,3,,,,NEIN;

/// ADD-LDAT:LROUTE=217,LSVC=VCE,LVAL=1,TGRP=90,ODR=1034,LAUTH=8,CARRIER=4,ZONE=EMPTY,LATTR=NONE,VCCYC=4;

/// ADD-LDAT:LROUTE=217,LSVC=VCE,LVAL=1,TGRP=1,ODR=1034,LAUTH=8,CARRIER=4,ZONE=EMPTY,LATTR=NONE,VCCYC=4;

/// ADD-LDAT:LROUTE=217,LSVC=DTE,LVAL=1,TGRP=1,ODR=1034,LAUTH=1,CARRIER=7,ZONE=EMPTY,LATTR=WCHREG,DNNO=8-5-701,VCCYC=4;

/// ADD-LDAT:LROUTE=218,LSVC=VCE,LVAL=1,TGRP=1,ODR=1034,LAUTH=1,CARRIER=7,ZONE=EMPTY,LATTR=WCHREG,VCCYC=4;

/// ADD-LDAT:LROUTE=218,LSVC=DTE,LVAL=1,TGRP=1,ODR=1034,LAUTH=1,CARRIER=7,ZONE=EMPTY,LATTR=WCHREG,VCCYC=4;

/// ADD-RICHT:MODE=LRTENEW,LRTE=217,LSVC=VCE,NAME="",TGRP=90&1,DNNO=8-5-100,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,PLB=NO,ROUTATT=NO,EMCYRTT=NO,INFO="",PDNNO=0,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO;

/// ADD-RICHT:MODE=LRTEEXT,LRTE=217,LSVC=DTE,TGRP=1;

/// ADD-RICHT:MODE=LRTENEW,LRTE=218,LSVC=VCE,NAME="",TGRP=1,DNNO=8-5-701,DTMFCNV=FIX,DTMFDISP=DIGITS,DTMFTEXT="MFVWAHL ",DTMFPULS=PP300,PLB=NO,ROUTATT=NO,EMCYRTT=NO,INFO="",PDNNO=0,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO;

/// ADD-RICHT:MODE=LRTEEXT,LRTE=218,LSVC=DTE,TGRP=1;

ADD-LODR:ODR=1034,CMD=OUTPULSE,DGTS=4969;

ADD-LODR:ODR=1034,CMD=ECHO,FIELD=3;

ADD-LODR:ODR=1034,CMD=ECHOALL;

ADD-LODR:ODR=1034,CMD=NPI,NPI=ISDN,TON=INTERNAT;

ADD-LODR:ODR=1034,CMD=END;

Steffen.Baier
Level 1
Level 1

‎03-06-2007 02:16 PM

97000 is the code to get to germany

ADD-LDPLN:97000-X,,900,,11,,,,NEIN;

/// ADD-LDAT:LROUTE=900,LSVC=ALL,LVAL=1,TGRP=1,ODR=900,LAUTH=11,CARRIER=9,ZONE=EMPTY,VCCYC=4;

/// ADD-RICHT:MODE=LRTENEW,LRTE=900,LSVC=ALL,NAME="DRKW FFM ",TGRP=1,DNNO=18-5-700,DTMFTEXT="",ROUTATT=NO,EMCYRTT=NO,INFO="",PDNNO=0,CHARCON=NEUTRAL,CONFTONE=NO,RERINGRP=NO,NOPRCFWD=NO,NITO=NO;

ADD-LODR:ODR=900,CMD=OUTPULSE,DGTS=4969123;

ADD-LODR:ODR=900,CMD=ECHO,FIELD=2;

ADD-LODR:ODR=900,CMD=NPI,NPI=ISDN,TON=INTERNAT;

ADD-LODR:ODR=900,CMD=END;

On call manager we have set in the gateway settings that the called and the calling party number use international format.

Called and Calling Numbering Plan is ISDN

Numbers to strip are 3 (acces code and 00 international code)

Caller id dn = 441234xxxx

Please let me know if you have any more issues or questions.

The isdn contiguous-bchan is only working with EcmaV2. If you really need to run EcmaV1 you will need the other command.

Our 37xx run the following:

dial-peer voice 4969123 pots

destination-pattern 4969123

incoming called-number .

direct-inward-dial

port 4/0:15

forward-digits all

And we added to London:

dial-peer voice 4969123 voip

destination-pattern 4969123T

voice-class codec 99

session target ipv4:10.196.152.190

incoming called-number .

dtmf-relay h245-alphanumeric

ip qos dscp cs5 media

ip qos dscp cs5 signaling

Customers Also Viewed These Support Documents