08-02-2018 01:04 PM - edited 03-18-2019 12:29 PM
Hi Guys,
My Customer have a Gateway 2921 with SIP Configured. In this equipment too having a FXO that not is identify the Caller ID. The Carrier told that identifier call is enable. Below the configuration FXO port. Are there another configuration to do in FXO interface?
voice-port 0/0/1
supervisory disconnect dualtone mid-call
cptone BR
timeouts call-disconnect 5
timeouts wait-release 5
connection plar 6556
station-id name TRONCO-NET
caller-id enable
Currently, when I dialed to number the User verify in the display only information: TRONCO-NET and not appear the number.
Any have idea about this?
Thanks,
Wilson
08-02-2018 01:56 PM
Hi.
You only have a name defined for that FXO Port. You also need to set a station number. Station-id number 12345.
08-02-2018 01:59 PM
Hi Janis,
Thanks a lot for Your contact. In station-id number I need put the number of the line?
Regards,
Wilson
08-02-2018 06:16 PM
Sorry thought this was a FXS port. If you want caller ID that is sent from telco, ensure that telco is providing caller ID to enable this. you can do a debug "voice ccapi inout" to see if telco is sending caller id.
08-03-2018 05:35 AM
Hi Janis,
No problem, don´t worry. Today will to do test. I will inform to You about the results, Ok.
Regards,
Thanks,
Wilson
08-03-2018 09:06 AM
08-03-2018 09:56 AM
Hi Nipun,
Thanks a lot by Your usual help. Today My co-worker will in the office and We will put analogic phone with call identifier. I will verify the number of rings as You are mentioning. After to do test I will inform the results.
Thanks,
Regards,
Wilson
08-03-2018 12:11 PM
Hi Nipun,
My Co-worker take the line FXO and put the Analogic Telephony with Caller Identifier and did test of call and number is show in the displayl.
Thanks,
Regards,
Wilson
08-06-2018 06:27 AM
Hi Nipun,
In the last friday was did the test. My co-worked putted the line in Analogic Telephony with Caller Identifier and the Carrier is send the number corretly. When return to gateway appear with unknow number. The next step will run debug in the FXO to try identify the that can be occur.
08-03-2018 12:12 PM
Hi Janis,
My Co-worker take the line FXO and put the Analogic Telephony with Caller Identifier and did test of call and number is show in the displayl.
Thanks,
Regards,
Wilson
08-06-2018 09:05 AM
08-06-2018 12:29 PM
Hi Nipun,
The User not is in the office now and my co-worker don´t remember how many rings was it? Tomorrow I can new test and came back with the answer, Ok.
Thanks,
Regards,
Wilson
08-07-2018 12:19 PM
Hi Nipun,
The interface already this configuration:
voice-port 0/0/1
supervisory disconnect dualtone mid-call
cptone BR
timeouts call-disconnect 5
timeouts wait-release 5
connection plar 6556
caller-id enable
caller-id alerting ring 2
Thanks,
Regards,
Wilson
08-21-2018 01:00 PM
Hi Nipun,
Sorry by delay. Was add the command:
sip-ua
timers buffer-invite 500
But, the fxo when received the call continues show: unknown number
Regards,
Wilson
08-06-2018 06:28 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide