06-06-2024 01:36 AM - edited 06-06-2024 01:37 AM
I have Route Group assigned to 2 Route Group Members and as ordered by priority calls will go to first E1!!
My question is how can I send call through second E1!
Needed for torubleshooting purposes!
Thank you
Solved! Go to Solution.
06-06-2024 01:51 AM
Hi @lana1
You can configure a new Route Pattern with a new partition, this partition should only be included in the CSS of the device you're making the test calls from.
This Route pattern will point to a new Route List, which points to a new Route Group that only has the specific slot you wanna send the call to.
Outbound calls for other devices will not be affected, since their CSS will not have the partition of the newly configured RP
06-06-2024 02:11 AM
As @eyalraba wrote, if you want to just use one E1 for testing, you have to build a different call routing structure.
06-06-2024 01:39 AM
Just switch the order in the Route group^^ Or set the algorithm to "Circular"
06-06-2024 01:46 AM
Thanks for reply!
No, I don't want to change the priority!
In traditional telephony, ex. MD110 there was possibility to make call through specific slot!
I want to send call through second E1, for testing and troubleshooting!!!
Thank you
06-06-2024 01:51 AM
Hi @lana1
You can configure a new Route Pattern with a new partition, this partition should only be included in the CSS of the device you're making the test calls from.
This Route pattern will point to a new Route List, which points to a new Route Group that only has the specific slot you wanna send the call to.
Outbound calls for other devices will not be affected, since their CSS will not have the partition of the newly configured RP
06-06-2024 02:22 AM
Done
Thank you very much!
06-06-2024 02:11 AM
As @eyalraba wrote, if you want to just use one E1 for testing, you have to build a different call routing structure.
06-06-2024 02:24 AM
Can I make additional question here!!!
Debug in Cisco 4331outcome is in Hexadecimal!!
How to chnge in Decimal!!!
Thank you!!
06-06-2024 02:33 AM
Can you share an example output, of what exactly to you mean?
06-06-2024 02:42 AM
Pls see below!!
I have this problem now in all gateway endpoints!!
005749: Jun 5 08:42:57.297: ISDN Se0/1/0:15 Q931d: srl_send_l3_pak:
source_id = CCM MANAGER 0x0003, dest_id = Q.921 0x0000, prim = DL_DATA_REQ 0x0240
priv_len = 4 int_id = 0x0x7FCB1FCB8938 datasize = 29
005750: Jun 5 08:42:57.297: ISDN Se0/1/0:15 Q931d: data =
005751: Jun 5 08:42:57.297: 00007FCB1FCB89380000000302400400
005752: Jun 5 08:42:57.297: 00010000080200544508028090
005753: Jun 5 08:42:57.316: ISDN Se0/1/0:15 Q931d: srl_send_l3_pak:
source_id = CCM MANAGER 0x0003, dest_id = Q.921 0x0000, prim = DL_DATA_REQ 0x0240
priv_len = 4 int_id = 0x0x7FCB1FCB8938 datasize = 25
005754: Jun 5 08:42:57.316: ISDN Se0/1/0:15 Q931d: data =
005755: Jun 5 08:42:57.316: 00007FCB1FCB89380000000302400400
005756: Jun 5 08:42:57.316: 00010000080200545A
06-06-2024 02:50 AM
What debugs have you enabled?
If you're troubleshooting calls for ISDN connection, just run the command "debug isdn q931"
06-06-2024 02:51 AM
debug isdn q931 detail
06-06-2024 03:02 AM
If you don't want to change the priority, then change the distribution algorithm to Circular.
06-06-2024 03:06 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide