06-18-2012 02:24 PM - edited 03-16-2019 11:43 AM
Hi All
The IT department in one branch office is planning to connect one of the PSTN links from the Lecagy PBX to the VoIP Router, I would like to know people if my VoIP router is hardware prepared for that change. (I already know's the configuration).
Here is some information:
controller E1 0/0/0
framing NO-CRC4
channel-group 0 timeslots 1-31
description VPN Telmex
!
controller E1 0/0/1
framing NO-CRC4
clock source internal
channel-group 0 timeslots 1-31
description VPN Telmex-2
!
controller E1 0/1/0
framing NO-CRC4
clock source free-running
pri-group timeslots 1-31
description Enlace Conmutador Loop 12
!
controller E1 0/1/1
framing NO-CRC4
clock source free-running
pri-group timeslots 1-31
description Enlace Conmutador Loop 41
!
controller E1 0/2/0
shutdown
framing NO-CRC4
clock source internal
!
controller E1 0/2/1
shutdown
framing NO-CRC4
!
controller E1 4/0
shutdown
framing NO-CRC4
!
controller E1 4/1
shutdown
framing NO-CRC4
NAME: "3845 chassis", DESCR: "3845 chassis"
PID: CISCO3845 , VID: V01 ,
NAME: "c3845 Motherboard with Gigabit Ethernet", DESCR: "c3845 Motherboard with Gigabit Ethernet"
PID: CISCO3845-MB , VID: V03
NAME: "Two port E1 voice interface daughtercard", DESCR: "Two port E1 voice interface daughtercard"
PID: VWIC-2MFT-E1= , VID: 1.0,
NAME: "Two port E1 voice interface daughtercard", DESCR: "Two port E1 voice interface daughtercard"
PID: VWIC-2MFT-E1= , VID: 1.0,
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 ,
NAME: "2nd generation four port FXO voice interface daughtercard", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V03 ,
NAME: "PVDMII DSP SIMM with four DSPs", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: NA ,
NAME: "PVDMII DSP SIMM with four DSPs", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: NA ,
NAME: "PVDMII DSP SIMM with four DSPs", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: NA ,
NAME: "High Density Voice2 Network module with on board two port interface ", DESCR: "High Density Voice2 Network module with on board two port interface "
PID: NM-HDV2-2T1/E1 , VID: V05 ,
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 ,
NAME: "PVDMII DSP SIMM with four DSPs", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 ,
NAME: "High Density Voice2 Network module with on board two port interface ", DESCR: "High Density Voice2 Network module with on board two port interface "
PID: NM-HDV2-2T1/E1 , VID: V04 ,
NAME: "2nd generation four port FXO voice interface daughtercard", DESCR: "2nd generation four port FXO voice interface daughtercard"
PID: VIC2-4FXO , VID: V03 ,
NAME: "PVDMII DSP SIMM with three DSPs", DESCR: "PVDMII DSP SIMM with three DSPs"
PID: PVDM2-48 , VID: V01 ,
NAME: "PVDMII DSP SIMM with one DSP with half channel capcity", DESCR: "PVDMII DSP SIMM with one DSP with half channel capcity"
PID: PVDM2-8 , VID: V01 ,
Cisco IOS Software, 3800 Software (C3845-SPSERVICESK9-M), Version 12.4(25c), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Fri 12-Feb-10 03:18 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T5, RELEASE SOFTWARE (fc1)
System returned to ROM by power-on
System image file is "flash:c3845-spservicesk9-mz.124-25c.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 3845 (revision 1.0) with 743424K/43008K bytes of memory.
Processor board ID FTX0953C2M9
2 Gigabit Ethernet interfaces
64 Serial interfaces
8 Channelized E1/PRI ports
4 Channelized (E1 or T1)/PRI ports
8 Voice FXO interfaces
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
62720K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102
Do I have enogh RAM and DSP's?
Do you have an advice for me?
Regards.
Solved! Go to Solution.
06-18-2012 10:30 PM
Hi
You have lots of hardware.
You should find out what type (physically, e.g. analogue, e1, rj48/45 or bnc) and signalling method (QSIG, DPNSS? PRI?) the PBX will use...
For further advice it's probably best to describe your scenario more fully...
Aaron
06-18-2012 02:29 PM
You've got plenty of hardware to at least connect 4-8 E1s
Regards,
Erik
Sent from Cisco Technical Support iPad App
06-18-2012 10:30 PM
Hi
You have lots of hardware.
You should find out what type (physically, e.g. analogue, e1, rj48/45 or bnc) and signalling method (QSIG, DPNSS? PRI?) the PBX will use...
For further advice it's probably best to describe your scenario more fully...
Aaron
08-22-2012 07:52 AM
Thanks, it was, It is just I think I needed more DSP's beause I only got 27 TDM ports configureng my E1 cause of the lack of DSP's
Thank you.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide