08-22-2020 03:31 AM
Hello guys
I saw in release notes that the ISR 1100 will support CUBE from 16.9 but no word about CME. Is CME going to be supported in some release or it will not be supported at all? If CME is supported this will be the perfect router.
Thanks
08-22-2020 04:00 AM
CME is not supported on ISR 1XXX based on the latest CME versions guide.
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cusrst/requirements/guide/srs128spc.html
Unified SRST 12.8 is only supported by the following platforms running Cisco IOS XE Amsterdam 17.2.X and later releases.
For Cisco 4000 Series Integrated Services Routers and Cisco VG400 Series Analog Voice Gateway platforms (Cisco VG400, Cisco VG450 and so on) that act as client gateways, all NIMs with FXS ports are supported when registered to Unified SRST using SCCP/STCAPP.
Supported Platforms and Memory Specifications: SCCP/SIP IP Phones* | |||||
Cisco Platform | Maximum SCCP/SIP IP Phones | Maximum Total Ephone-dns or Virtual Ports | Recommended DRAM in Non-Secure Cisco Unified SRST | Recommended DRAM in Secure Cisco Unified SRST | Recommended Flash Memory |
Cisco ISR 4321 | 50 | 200 | 4 GB | 4 GB | 4 GB |
Cisco ISR 4331 | 100 | 400 | 4 GB | 4 GB | 4 GB |
Cisco ISR 4351 | 700 | 1000 | 4 GB | 4 GB | 4 GB |
Cisco ISR 4431 | 1200 | 1800 | 4 GB | 4 GB | 8 GB |
Cisco ISR 4451 | 2000 | 2500 | 4 GB | 4 GB | 8 GB |
Cisco ISR 4461 | 2000 | 2500 | 8 GB | 8 GB | 8 GB |
* Memory recommendations and maximum numbers of IP phones are for common Cisco SRST configurations only. Systems with large numbers of phones and complex configurations may not work on all platforms and can require additional memory or a higher performance platform. The Maximum Total IP Phones can be split between SCCP and SIP phones as long as the maximum total of IP phones is not exceeded. |
08-22-2020 04:21 AM
Thanks for the replay
Yes, I know that in Amsterdam it is not supported, the question is, is it going to be supported in future releases
08-22-2020 07:29 AM
Roadmap is NDA, thus, it cannot be discussed in public forums. Reach out to your SE for this question.
05-10-2021 10:26 AM
Hi,
I have a ISR1100-4P and I adquiere CME licences for this ISR.
ISRCME#show license summary
License Usage:
License Entitlement Tag Count Status
-----------------------------------------------------------------------------
uck9 (ISR_1100_4P_UnifiedCom...) 1 IN USE
securityk9 (ISR_1100_4P_Security) 1 IN USE
The IOS software is:
Cisco IOS Software [Amsterdam], ISR Software (ARMV8EL_LINUX_IOSD-UNIVERSALK9-M), Version 17.3.3, RELEASE SOFTWARE (fc7)
I can't use CME here, Do I lost anyone? The command "telephony-service" doesn't exit.
Regards.
05-10-2021 11:36 AM
Please upgrade to 17.5.1a. This is the first release to support CME. Previous versions only supports CUBE functionality.
home-gw(config)#telephony-service ?
setup Start setup for Cisco Unified Communications Manager Express. Please
refer to
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/tsd_products_support_series_home.html
for full documentation.
<cr> <cr>
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide