I am trying to assist my uncle with setup of a PRI on their CME router. I've created the pri-group and I can see the channels are good and the call comes in, but always end in fast busy. I do not see the voice-port populating after created the pri-group. I'm stumped on why the voice port is not created for setting bearer cap.
I am expecting to see a section of my running-config, but it does not come up:
!
voice-port 0/3/0:23
bearer-cap speech
!
sh isdn stat
Global ISDN Switchtype = primary-ni
ISDN Serial0/3/0:23 interface
dsl 0, interface ISDN Switchtype = primary-ni
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x800003FF
Number of L2 Discards = 0, L2 Session ID = 1
Total Allocated ISDN CCBs = 0
sh isdn serv
PRI Channel Statistics:
ISDN Se0/3/0:23, Channel [1-24]
Configured Isdn Interface (dsl) 0
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4
State : 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3 3 3 3 3 3 3 3 3
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4
State : 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2
Here are my first results:
chrs-phx-cme#
Dec 11 05:48:03.655: ISDN Se0/3/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0DAA
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18381
Preferred, Channel 1
Facility i = 0x9F8B0100A10D02010102010080055445584153
Protocol Profile = Networking Extensions
0xA10D02010102010080055445584153
Component = Invoke component
Invoke Id = 1
Operation = CallingName
Name Presentation Allowed Extended
Name = TEXAS
Calling Party Number i = 0x2180, 'xxxxxx9001'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, 'xxxxxx5159'
Plan:ISDN, Type:National
Dec 11 05:48:03.655: ISDN Se0/3/0:23 Q931: Received SETUP callref = 0x8DAA callID = 0x0411 switch = primary-ni interfac
e = User
Dec 11 05:48:03.655: ISDN Se0/3/0:23 **ERROR**: accept_incoming_csm_call: modem problem Bearer capability not available(
0x3A): b channel 0, call id 0x411
Dec 11 05:48:03.659: ISDN Se0/3/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8DAA
Channel ID i = 0xA98381
Exclusive, Channel 1
Dec 11 05:48:03.659: ISDN Se0/3/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x8DAA
Cause i = 0x80BA - Bearer capability not available
chrs-phx-cme#
Dec 11 05:48:03.679: ISDN Se0/3/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x0DAA
Dec 11 05:48:03.679: ISDN Se0/3/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8DAA
chrs-phx-cme#
In CME I added the 5159 to a user as the Primary E.164 Number, and that gave me the following result:
Dec 11 06:08:13.919: ISDN Se0/3/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0DBA
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18381
Preferred, Channel 1
Facility i = 0x9F8B0100A10D02010102010080055445584153
Protocol Profile = Networking Extensions
0xA10D02010102010080055445584153
Component = Invoke component
Invoke Id = 1
Operation = CallingName
Name Presentation Allowed Extended
Name = TEXAS
Calling Party Number i = 0x2180, 'xxxxxx9001'
Plan:ISDN, Type:National
Called Party Number
chrs-phx-cme# i = 0xA1, 'xxxxxx5159'
Plan:ISDN, Type:National
Dec 11 06:08:13.919: ISDN Se0/3/0:23 Q931: Received SETUP callref = 0x8DBA callID = 0x0002 switch = primary-ni interfac
e = User
Dec 11 06:08:13.919: ISDN Se0/3/0:23 **ERROR**: call_incoming: Received a call id 0x2 with a bad bearercap from 91552690
01 on b channel 1
Dec 11 06:08:13.923: ISDN Se0/3/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8DBA
Cause i = 0x80C1 - Bearer capability not implemented
chrs-phx-cme#
Here are the basics:
Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 15.1(3)T, RELEASE SOFTWARE (fc1)
NAME: "1 port channelized and PRI T1/E1 HWIC on Slot 0 SubSlot 3", DESCR: "1 port channelized and PRI T1/E1 HWIC"
PID: HWIC-1CE1T1-PRI , VID: V02 ,
Running Config:
!
card type t1 0 3
logging buffered 300000
!
no aaa new-model
clock timezone ARIZONA -7 0
no network-clock-participate wic 3
!
dot11 syslog
ip source-route
!
!
ip cef
!
!
!
no ip domain lookup
ip name-server 192.168.0.2
no ipv6 cef
multilink bundle-name authenticated
!
stcapp ccm-group 2
!
stcapp supplementary-services
port 0/2/0
fallback-dn 121
!
!
!
isdn switch-type primary-ni
!
!
trunk group 1
!
!
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
!
voice class custom-cptone leavetone
dualtone conference
frequency 400 800
cadence 400 50 200 50 200 50
!
voice class custom-cptone jointone
dualtone conference
frequency 600 900
cadence 300 150 300 100 300 50
!
!
!
!
voice translation-rule 1
rule 1 /1../ /xxxxxxxxxx/
!
!
voice translation-profile outgoing
translate calling 1
!
!
voice-card 0
dsp services dspfarm
!
crypto pki token default removal timeout 0
!
!
!
!
!
controller T1 0/3/0
clock source internal
cablelength long 0db
pri-group timeslots 1-10,24
!
ip ssh version 2
!
!
!
!
!
interface Serial0/3/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
no cdp enable
!
interface Service-Engine1/0
ip unnumbered GigabitEthernet0/1
service-module ip address 192.168.0.9 255.255.255.0
service-module ip default-gateway 192.168.0.2
!
ip forward-protocol nd
!
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
!
ip route 0.0.0.0 0.0.0.0 192.168.0.1
ip route 0.0.0.0 0.0.0.0 192.168.0.2
ip route 192.168.0.9 255.255.255.255 Service-Engine1/0
!
!
!
control-plane
!
!
voice-port 0/0/0
trunk-group 1
connection plar 774
description 602.246.7607
caller-id enable
!
voice-port 0/0/1
trunk-group 1
connection plar 774
description 602.246.0310
caller-id enable
!
voice-port 0/0/2
trunk-group 1
connection plar 774
description 602.246.0954
caller-id enable
!
voice-port 0/0/3
trunk-group 1
connection plar 774
description 602.277.4233
caller-id enable
!
voice-port 0/1/0
trunk-group 1
connection plar 774
shutdown
description 602.264.1518
caller-id enable
!
voice-port 0/1/1
trunk-group 1
connection plar 774
shutdown
description 602.264.1705
caller-id enable
!
voice-port 0/1/2
timeouts call-disconnect 3
shutdown
caller-id enable
!
voice-port 0/1/3
no battery-reversal
shutdown
!
voice-port 0/2/0
timeouts ringing infinity
description Bogen Paging Adapter
!
voice-port 0/2/1
!
voice-port 0/2/2
!
voice-port 0/2/3
!
!
!
mgcp profile default
!
sccp local GigabitEthernet0/1
sccp ccm 192.168.0.8 identifier 100 priority 1 version 4.1
sccp
!
sccp ccm group 2
bind interface GigabitEthernet0/1
associate ccm 100 priority 1
associate profile 2 register DSPprofile2
keepalive retries 5
!
dspfarm profile 2 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
conference-join custom-cptone jointone
conference-leave custom-cptone leavetone
associate application SCCP
shutdown
!
dial-peer voice 10 voip
destination-pattern 778
session protocol sipv2
session target ipv4:192.168.0.9
codec g711ulaw
no vad
!
dial-peer voice 11 voip
destination-pattern 779
session protocol sipv2
session target ipv4:192.168.0.9
codec g711ulaw
no vad
!
dial-peer voice 777 voip
description Cisco Unity Express voicemail pilot number
destination-pattern 777
session protocol sipv2
session target ipv4:192.168.0.9
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 776 voip
description Cisco Unity AA
destination-pattern 776
session protocol sipv2
session target ipv4:192.168.0.9
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 775 voip
description Cisco Unity AA-admin
destination-pattern 775
session protocol sipv2
session target ipv4:192.168.0.9
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 9 pots
trunkgroup 1
description PRI
destination-pattern 9T
no sip-register
!
dial-peer voice 443 pots
destination-pattern 443
port 0/1/3
forward-digits 0
!
dial-peer voice 444 pots
description Bogen Paging Adapter
service stcapp
port 0/2/0
!
!
!
!
card type t1 0 3
logging buffered 300000
!
no aaa new-model
clock timezone ARIZONA -7 0
no network-clock-participate wic 3
!
dot11 syslog
ip source-route
!
!
ip cef
!
!
!
no ip domain lookup
ip name-server 192.168.0.2
no ipv6 cef
multilink bundle-name authenticated
!
stcapp ccm-group 2
!
stcapp supplementary-services
port 0/2/0
fallback-dn 121
!
!
!
isdn switch-type primary-ni
!
!
trunk group 1
!
!
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
!
voice class custom-cptone leavetone
dualtone conference
frequency 400 800
cadence 400 50 200 50 200 50
!
voice class custom-cptone jointone
dualtone conference
frequency 600 900
cadence 300 150 300 100 300 50
!
!
!
!
voice translation-rule 1
rule 1 /1../ /xxxxxxxxxx/
!
!
voice translation-profile outgoing
translate calling 1
!
!
voice-card 0
dsp services dspfarm
!
crypto pki token default removal timeout 0
!
!
!
!
!
controller T1 0/3/0
clock source internal
cablelength long 0db
pri-group timeslots 1-10,24
!
ip ssh version 2
!
!
!
!
!
interface Serial0/3/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
no cdp enable
!
interface Service-Engine1/0
ip unnumbered GigabitEthernet0/1
service-module ip address 192.168.0.9 255.255.255.0
service-module ip default-gateway 192.168.0.2
!
ip forward-protocol nd
!
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
!
ip route 0.0.0.0 0.0.0.0 192.168.0.1
ip route 0.0.0.0 0.0.0.0 192.168.0.2
ip route 192.168.0.9 255.255.255.255 Service-Engine1/0
!
!
!
control-plane
!
!
voice-port 0/0/0
trunk-group 1
connection plar 774
description 602.246.7607
caller-id enable
!
voice-port 0/0/1
trunk-group 1
connection plar 774
description 602.246.0310
caller-id enable
!
voice-port 0/0/2
trunk-group 1
connection plar 774
description 602.246.0954
caller-id enable
!
voice-port 0/0/3
trunk-group 1
connection plar 774
description 602.277.4233
caller-id enable
!
voice-port 0/1/0
trunk-group 1
connection plar 774
shutdown
description 602.264.1518
caller-id enable
!
voice-port 0/1/1
trunk-group 1
connection plar 774
shutdown
description 602.264.1705
caller-id enable
!
voice-port 0/1/2
timeouts call-disconnect 3
shutdown
caller-id enable
!
voice-port 0/1/3
no battery-reversal
shutdown
!
voice-port 0/2/0
timeouts ringing infinity
description Bogen Paging Adapter
!
voice-port 0/2/1
!
voice-port 0/2/2
!
voice-port 0/2/3
!
!
!
mgcp profile default
!
sccp local GigabitEthernet0/1
sccp ccm 192.168.0.8 identifier 100 priority 1 version 4.1
sccp
!
sccp ccm group 2
bind interface GigabitEthernet0/1
associate ccm 100 priority 1
associate profile 2 register DSPprofile2
keepalive retries 5
!
dspfarm profile 2 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
conference-join custom-cptone jointone
conference-leave custom-cptone leavetone
associate application SCCP
shutdown
!
dial-peer voice 10 voip
destination-pattern 778
session protocol sipv2
session target ipv4:192.168.0.9
codec g711ulaw
no vad
!
dial-peer voice 11 voip
destination-pattern 779
session protocol sipv2
session target ipv4:192.168.0.9
codec g711ulaw
no vad
!
dial-peer voice 777 voip
description Cisco Unity Express voicemail pilot number
destination-pattern 777
session protocol sipv2
session target ipv4:192.168.0.9
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 776 voip
description Cisco Unity AA
destination-pattern 776
session protocol sipv2
session target ipv4:192.168.0.9
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 775 voip
description Cisco Unity AA-admin
destination-pattern 775
session protocol sipv2
session target ipv4:192.168.0.9
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 9 pots
trunkgroup 1
description PRI
destination-pattern 9T
no sip-register
!
dial-peer voice 443 pots
destination-pattern 443
port 0/1/3
forward-digits 0
!
dial-peer voice 444 pots
description Bogen Paging Adapter
service stcapp
port 0/2/0
!
!3/0
