12-26-2011 10:48 PM - edited 03-16-2019 08:42 AM
Hello!
Please help..I`m trying to set up a new CUCM 8.6.1(a). All is well, but it`s impossible to configure pass calls through h323-gateway. Appropriate route-patterns and CSS are configured. Incoming calls over this h323-trunk successfully come to call-manager, but an outgoing call I hear the tube short beeps. I note that if I make the inter-cluster trunk, everything works in both directions.
P.S. On my existing CUCM 7.1.5 this problem did not exist.
01-11-2012 02:35 AM
Hi Dmitry,
Can you add bearer-cap speech under voice port like below just for testing
voice-port 0/3/0:15
bearer-cap speech
Regards,
Senthil
01-11-2012 02:40 AM
Hi SenthilKumar,
don`t direct attention on my IOS-gateway. In parallel with the CUCM 8.6.1 I have the CUCM 7.1.5 with identical settings, which works fine.I can use various devices on another side of my 323-trunk and outgoing calls won't work. My problem - directly in CUCM 8.6.1
P.S. I try to add bearer-cap speech - still not work
01-11-2012 02:45 AM
Hi Dmitry,
In CUCM CDR, do you see the 88 cause code released by source or destination. If it is destination can you share the complete set of logs like CM Services, debug isdn q931 and debug voip dial-peer inout
Regards,
Senthil
01-11-2012 02:50 AM
Hi SenthilKumar,
It`s a source 88-code which generated by CUCM and I can see any traffic on my IOS-gateway.
01-11-2012 05:41 AM
Hi Dmitry,
Can you share the logs for the failed call, so that we can check on that
Regards,
senthil
01-11-2012 05:49 AM
01-12-2012 12:59 AM
Hi Dmitry,
Call Manager sends the Setup Message to the Gateway and immediately it gets Realease Messages with Incompatable Destination as the cause.
Setup Message : Sent
SETUP, pd = 8, callref = 0x0004
Bearer Capability i = 0x0800900A2, ITU-T standard, Speech, Circuit mode, 64k, mu-law
Display i = 'Bond'
Calling Party Number i = '44002' - Plan: Unknown,Type: Unknown, Presentation Allowed,User-provided, verified and passed
Called Party Number i = '12345' - Plan: Unknown,Type: Unknown
Release Message : Received
RELEASE_COMP, pd = 8, callref = 0x8004
Cause i = 0x0810D8 - Incompatible destination
Did you had any chance to take the IOS Gateway Logs. If you have those please share. We may have to look how gateway treats this SETUP message.
Regards,
Senthil
01-13-2012 12:15 AM
Hi Dmitry,
Did you get any chance to find the issue.
Regards,
Senthil
01-13-2012 12:37 AM
Hi SenthilKumar,
problem with IOS-gateways was successfully resolved. There was a tall-fraud prevention issue on my router.
But problem with any 3d-party h323 gateways (etc. Avaya) still actually. When I make outgoing call from CUCM-Phone to Avaya-Phone then I have in CUCM logs cause code (34) no circuit/channel available
06-26-2015 10:22 PM
just a note, noticed your second controller is shutdown.
Sent from Cisco Technical Support iPhone App
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide