02-18-2014 08:14 AM - edited 03-16-2019 09:48 PM
Hi guys,
I am newbie in VG systems and i dont have any docu, i need to congiure 4 faxes with a cme in a VG204, my problem is to find some help to configure this VG and what i need to add in my CME, the ethernet interface its done and works well but i dont know the config for voice-port 0 , 1 , 2 and 3. (The 4 faxes).
Thx in advance and sorry for my bad english.
02-18-2014 12:12 PM
Hi,
Here is is a useful snip from the cme config guide:-
Regards,
Alex.
Please rate useful posts.
02-18-2014 02:30 PM
Hi Juan,
Hope this link helps you out:
https://supportforums.cisco.com/thread/2127686
Here is an example of the configuration you will need to do. (This is not layed out in exact order)
On the VG204
Interface VLAN 1
IP Address 10.0.0.1
sccp local VLAN 1
sccp ccm 1.1.1.1 identifier 1 priority 1 <----- The IP Address here would be the IP Address of your CUCME
sccp
sccp ccm group 1
bind interface VLAN 1
associate ccm 1 priority 1
stcapp ccm-group 1
stcapp
ccm-manager config server 1.1.1.1
ccm-manager config
ccm-manager sccp
ccm-manager sccp local VLAN 1
For every FXS port create a dial-peer as seen below:
Dial-peer voip 1 pots
service stcapp <---- This is what puts the FXS port under SCCP control.
port 0/0/0
On the CUCME (Pre-configured)
Configure the VG204 Gateway on CUCME as seen below:
voice-gateway system 1
network-locale FR
type VG224
mac-address 1234.5678.9999
voice-port 0-23
create cnf-files
For the analog phone you can configure auto-registration if you wish to or manually add the phones.
Automatically register ephones:
Under the Telephony-service add the following command
auto assign 1 to 24 type anl
— Use the type keyword if you have other phone types in the system and you want only the analog endpoints to be assigned to ephone-dns automatically.
To add a ephone manually read the following:
The VG202 and VG204 voice gateways use the MAC address of the Skinny Call Control Protocol (SCCP) local interface to define unique MAC addresses for each voice port by using the last 9 digits of the SCCP local interface of the voice gateway.
For example, if the source interface MAC address is 000C.8639.5833, the MAC address of the voice port MAC address will be C863.9583.3XXX. In the preceding example, the last 9 digits of the SCCP of the local VG202 or VG204 voice gateway become the first 9 digits of the voice port MAC address after dropping the leading 000.
The last 3 digits of the voice port MAC address is the slot number (3-bit) + subunit number (2-bit) + port number (7-bit) in hexadecimal format. You combine the digits to get the last three MAC address digits.
For example, the voice-port 0/0 is slot number 0 (000): subunit 0 (00) and port number 0 (0000000). By stringing the digits together, you get the following: 0000 0000 0000 = 0 0 0. This means that if the source interface MAC address is 001f.cac3.b3f8, the MAC address of voice port 0/0 will be 1FCAC3b3f8000
Ephone example:
ephone 1
device-security-mode none
mac-address 1234.5678.9000
button 1:1
ephone 2
device-security-mode none
mac-address 1234.5678.9001
button 1:1
Regards,
Kevin
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide