04-27-2015 08:07 AM - edited 03-17-2019 02:49 AM
I'm trying to configure the second ISDN on the same gateway but I cannot get this working.
I would be grateful if I could have some help with the configuration? I need to send the incoming traffic for both ISDNs to the call manager. The config that i havefor the first ISDN;
Thanks
04-27-2015 08:16 AM
Hello,
What do you get when you try to configure the 2nd controller?
Thank you,
Shadi
04-27-2015 08:30 AM
Hi,
what is the number of time slots u are configuring for second E1 PRI?
In your existing E1 PRI, are u using first 24 TS[fractional PRI]
can u share complete config?
regds,
aman
04-27-2015 01:22 PM
well I didn't realise that I have to configure the second E1 :\
I'm not that familiar with the ISDN, can you guys please help me with configuring the second E1?
04-28-2015 12:46 AM
when I try to configure the second E1, i get this:
402-3(config)#controller E1 ?
<0-0> Controller slot number
so how i can configure the second one/
04-28-2015 12:46 AM
Hi,
If u have dual port E1 card , then u need to configure controller e1 0/0/1 since 0/0/0 is already configured.
regds,
aman
04-28-2015 12:52 AM
I dont have dual port.
402-3(config)#controller E1 0/0/?
<0-0> Controller port number
04-28-2015 01:10 AM
If u do not have second E1 port available, then u won't be able to configure.
accordingly, u need to buy one E1 port card if router has slot available or replace the existing card with Dual E1 port card.
regds,
amn
04-28-2015 01:16 AM
this is the output from show hardware:
Cisco CISCO2911/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FCZ183171K3
3 Gigabit Ethernet interfaces
24 Serial interfaces
5 ISDN Basic Rate interfaces
1 terminal line
1 Channelized E1/PRI port
DRAM configuration is 64 bits wide with parity enabled.
04-28-2015 01:27 AM
I suppose , you want to configure BRI ports but u have been referring to E1 Controller.
can u share show diag and show inventory?
regds,
aman
04-28-2015 01:34 AM
402-3>en
Password:
tp-7402-3#show inven
tp-7402-3#show inventory
NAME: "CISCO2911/K9", DESCR: "CISCO2911/K9 chassis, Hw Serial#: FCZ183171K3, Hw Revision: 1.0"
PID: CISCO2911/K9 , VID: V07 , SN: FCZ183171K3
NAME: "VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC3-1MFT-T1/E1 , VID: V01 , SN: FOC182816N7
NAME: "2nd generation two port BRI voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation two port BRI voice interface daughtercard"
PID: VIC2-2BRI-NT/TE= , VID: V , SN: FOC08500PBH
NAME: "2nd generation two port BRI voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation two port BRI voice interface daughtercard"
PID: VIC2-2BRI-NT/TE , VID: V01 , SN: FOC10442HLS
NAME: "Wan Interface Card BRI U (82912) on Slot 0 SubSlot 3", DESCR: "Wan Interface Card BRI U (82912)"
PID: HWIC-1B-U , VID: V03 , SN: FOC19039MH2
NAME: "PVDM3 DSP DIMM with 32 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 32 Channels"
PID: PVDM3-32 , VID: V01 , SN: FOC18297CKB
NAME: "C2911 AC Power Supply", DESCR: "C2911 AC Power Supply"
PID: PWR-2911-AC , VID: V05 , SN: QCS18201ZAD
402-3# show diag
Slot 0:
C2911 Mother board 3GE, integrated VPN and 4W Port adapter, 9 ports
Port adapter is analyzed
Port adapter insertion time 1w0d ago
EEPROM contents at hardware discovery:
PCB Serial Number : FOC18166KMN
Hardware Revision : 1.0
Part Number : 73-11833-12
Top Assy. Part Number : 800-30797-06
Board Revision : D0
Deviation Number : 0
Fab Version : 03
Product (FRU) Number : CISCO2911/K9
Version Identifier : V07
CLEI Code : CMMJD00ARA
Processor type : C1
Chassis Serial Number : FCZ183171K3
Chassis MAC Address : 88f0.31ae.7288
MAC Address block size : 80
Manufacturing Test Data : 00 00 00 00 00 00 00 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 38 31 36 36 4B 4D 4E 40
0x10: 06 18 41 01 00 82 49 2E 39 0C C0 46 03 20 00 78
0x20: 4D 06 42 44 30 88 00 00 00 00 02 03 CB 8C 43 49
0x30: 53 43 4F 32 39 31 31 2F 4B 39 89 56 30 37 20 D9
0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 4A 44 30 30 41 52
0x50: 41 09 C1 C2 8B 46 43 5A 31 38 33 31 37 31 4B 33
0x60: C3 06 88 F0 31 AE 72 88 43 00 50 C4 08 00 00 00
0x70: 00 00 00 00 00 F3 00 03 40 01 25 FF FF FF FF FF
0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Internal Power Supply information
Top Assy. Part Number : 341-0235-07
Deviation Number : 0
PCB Serial Number : QCS18201ZAD
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier : V05
Product (FRU) Number : PWR-2911-AC
CLEI Code :
Board Revision : A0
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 E5 DF 45 01 55 00 EB 07 88 00 00 00
0x10: 00 C1 8B 51 43 53 31 38 32 30 31 5A 41 44 03 00
0x20: 81 00 00 00 00 04 00 89 56 30 35 20 CB 8B 50 57
0x30: 52 2D 32 39 31 31 2D 41 43 C6 8A 00 00 00 00 00
0x40: 00 00 00 00 00 F3 00 59 41 00 C2 42 00 05 F8 00
0x50: 50 01 F4 10 38 02 EE 13 38 03 E8 15 9B 04 E2 17
0x60: B0 05 DC 1B 07 06 D6 1B FD 07 D0 1C CB 08 CA 1D
0x70: 83 09 C4 1E 21 0A BE 1E 8F 0B B8 1E F8 0D AC 1F
0x80: BC 0F A0 20 43 11 94 20 AA 13 88 21 68 17 70 21
0x90: 68 1B 58 21 A3 1F 40 21 B2 23 28 21 AC 27 10 21
0xA0: A6 42 41 30 FF FF FF FF FF FF FF FF FF FF FF FF
0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
PVDM Slot 0:
32-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card
Hardware Revision : 1.0
Part Number : 73-11577-03
Board Revision : D0
Deviation Number : 0
Fab Version : 03
PCB Serial Number : FOC18297CKB
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM3-32
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 D9 41 01 00 82 49 2D 39 03 42 44 30
0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 38 32 39
0x20: 37 43 4B 42 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 8F 50 56 44 4D 33 2D 33 32 20 20 20 20 20 20 20
0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
VWIC3-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1
Hardware Revision : 1.0
Top Assy. Part Number : 800-34657-01
Part Number : 73-13419-01
Board Revision : B0
Deviation Number : 0
Fab Version : 05
PCB Serial Number : FOC182816N7
Version Identifier : V01
Product (FRU) Number : VWIC3-1MFT-T1/E1
CLEI Code : COUIA7PCAA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 06 ED 41 01 00 C0 46 03 20 00 87 61 01
0x10: 82 49 34 6B 01 42 42 30 88 00 00 00 00 02 05 C1
0x20: 8B 46 4F 43 31 38 32 38 31 36 4E 37 89 56 30 31
0x30: 20 CB 90 56 57 49 43 33 2D 31 4D 46 54 2D 54 31
0x40: 2F 45 31 C6 8A 43 4F 55 49 41 37 50 43 41 41 03
0x50: 00 81 00 00 00 00 04 00 D9 03 40 C1 CB FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 1:
VIC2 - BRI-NT/TE Voice daughter card (2 port)
Hardware Revision : 1.1
Top Assy. Part Number : 800-21861-01
Board Revision : B0
Deviation Number : 0-0
Fab Version : 01
PCB Serial Number : FOC08500PBH
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Version Identifier : V
Product (FRU) Number : VIC2-2BRI-NT/TE=
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 51 41 01 01 C0 46 03 20 00 55 65 01
0x10: 42 42 30 80 00 00 00 00 02 01 C1 8B 46 4F 43 30
0x20: 38 35 30 30 50 42 48 03 00 81 00 00 00 00 04 00
0x30: 89 56 00 00 00 FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 2:
VIC2 - BRI-NT/TE Voice daughter card (2 port)
Hardware Revision : 1.1
Top Assy. Part Number : 800-21861-02
Board Revision : A0
Deviation Number : 0-0
Fab Version : 01
PCB Serial Number : FOC10442HLS
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VIC2-2BRI-NT/TE
Version Identifier : V01
CLEI Code : CNUIAPSAAA
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 51 41 01 01 C0 46 03 20 00 55 65 02
0x10: 42 41 30 80 00 00 00 00 02 01 C1 8B 46 4F 43 31
0x20: 30 34 34 32 48 4C 53 03 00 81 00 00 00 00 04 00
0x30: CB 8F 56 49 43 32 2D 32 42 52 49 2D 4E 54 2F 54
0x40: 45 89 56 30 31 20 C6 8A 43 4E 55 49 41 50 53 41
0x50: 41 41 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 3:
BRI U - 82912 WAN daughter card
Hardware Revision : 1.0
Top Assy. Part Number : 800-33017-02
Board Revision : A0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC19039MH2
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-1B-U
Version Identifier : V03
CLEI Code : COUIALACAC
Part Number : 73-12755-02
Fab Part Number : 28-7707-04
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 3D 41 01 00 C0 46 03 20 00 80 F9 02
0x10: 42 41 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 39 30 33 39 4D 48 32 03 00 81 00 00 00 00 04 00
0x30: CB 89 48 57 49 43 2D 31 42 2D 55 89 56 30 33 20
0x40: D9 02 40 C1 C6 8A 43 4F 55 49 41 4C 41 43 41 43
0x50: 82 49 31 D3 02 85 1C 1E 1B 04 FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Embedded Service Engine 0/0 :
Total platform memory : 524288K bytes
Total 2nd core memory : 0K bytes
Start of physical address for 2nd core : 0x80000000
Virtual address start of 2nd core memory : 0x0 - 0x0
2nd core configured disabled
L2 cache ways for 2nd core : 0
04-28-2015 02:01 AM
u are using BRI voice cards[ VIC2-2BRI-NT/TE].
you need to configure BRI instead of E1 PRI.
please refer the link
http://www.cisco.com/c/en/us/support/docs/voice/digital-ccs/15415-bri-voice-port-cfg.html
regds,
aman
04-28-2015 02:48 AM
I'm trying to configure the BRI. The BRI that I need to configure is BRI0/3/0, But when I want to configure the voice-port it says 0/3/0 is invalid.
04-28-2015 03:04 AM
It has to be bri0/1/0 or bri0/2/0 .
you are trying to configure for HWIC-1B-U which is used for WAN connectivity.
regds,
aman
04-28-2015 03:22 AM
these ports already got configured. still I cannot see any traffic for the new ISDN :/
maybe I bought the wrong card? I have got HWIC-1B-U in order to connect the second ISDN to the router.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide