Unable to configure voice-service dsp-reservation on cisco 2911

[RAJA RAHMAN]

Hello Experts 

Unable to configure voice-service dsp-reservation under voice-card 0

i am not able to see the option at all 

 HQ-Router(config-voicecard)#?
Voice-card configuration commands:
  codec         Manage codec configuration parameters for voice card
  default       Set a command to its defaults
  dsp           Manage DSP configuration for the voice card
  dspfarm       Enable dspFarm feature for this voice card (command will be deprecated in future releases, use the new command 'dsp
                tdm pooling')
  exit          Exit from voice card configuration mode
  local-bypass  Enable TDM hairpinning
  no            Negate a command or set its defaults

ios version c2900-universalk9-mz.SPA.151-2.T.bin"

NAME: "PVDM3 DSP DIMM with 16 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 16 Channels"
PID: PVDM3-16          , VID: V01 , SN: FOC19107FR2

and more over  i have pvdm 3-16 on this router and using only 4 channels of the pri . will i will be able to configure 1 video conference with 2 party .

Regards

RR  

[Wilson Samuel]

Hi

Could you please share the following:

1. Show inventory

2. sh sccp

I guess you have only PVDM-3 16 and all have been used already.

Regards

[RAJA RAHMAN]

Hello 

Please find the below 

HQ-Router#sh sccp
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0.102
        IPv4 Address: 142.102.64.254
        Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 142.100.64.11, Port Number: 2000
                Priority: 2, Version: 7.0, Identifier: 2
Call Manager: 142.100.64.12, Port Number: 2000
                Priority: 1, Version: 7.0, Identifier: 1

SCCP application services(dspfarm profiles) are not enabled 
or haven't associated to SCCP CCM group

HQ-Router#sh sccp
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0.102
        IPv4 Address: 142.102.64.254
        Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 142.100.64.11, Port Number: 2000
                Priority: 2, Version: 7.0, Identifier: 2
Call Manager: 142.100.64.12, Port Number: 2000
                Priority: 1, Version: 7.0, Identifier: 1

SCCP application services(dspfarm profiles) are not enabled 
or haven't associated to SCCP CCM group

I have just used inly 4 channel of the pri  as configured below  

controller T1 0/0/0
 shutdown 
 cablelength long 0db
!         
controller T1 0/0/1
 cablelength long 0db
 pri-group timeslots 1-4,24 service mgcp

Please advise 

regards

Raja

[Wilson Samuel]

Strange..

Could you please show us the Lic type on the router? It may be on IP Basic and not enabled for the Unified Communications.

Regards

[RAJA RAHMAN]

:(

Technology Package License Information for Module:'c2900' 
          
----------------------------------------------------------------
Technology    Technology-package          Technology-package
              Current       Type          Next reboot  
-----------------------------------------------------------------
ipbase        ipbasek9      Permanent     ipbasek9
security      None          None          None
uc            uck9          Evaluation    uck9
data          None          None          None
          
Configuration register is 0x2102
          

Index 1 Feature: ipbasek9                       
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Medium
Index 2 Feature: securityk9                     
        Period left: 8  weeks 4  days 
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
        License Count: Non-Counted
        License Priority: None
Index 3 Feature: uck9                           
        Period left: 8  weeks 3  days 
        License Type: Evaluation
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Low

Please help 

Regards

RR

[Wilson Samuel]

I think you may need more than 1 PVDM-3-16, as per the following document you cannot share the Cores between Voice and Video (i.e. fragmented cores).

Here is the excerpt:

There are some limitations for the allocation of PVDM3 for IPSLA VO that the user needs to be aware of. PVDM3 is reserved on the router using the IOS® command below:
voice-card 0
voice-service dsp-reservation <percentage>
#The above is for voice while the remaining DSP resources will be used for Video
IPSLA VO presently cannot use fragmented cores. A fragmented core is one that is allocated for both voice and video. This needs to be taken into consideration when procuring/provisioning PVDM3.

Also, here is a thread describing a similar incident

https://supportforums.cisco.com/discussion/11650346/cannot-create-video-conference-bridge-2921

HTH

[RAJA RAHMAN]

Hi 

can i mix pvdm 3-16  for video and  pvdm 2-64 for voice activity 

Please can you advise .

[RAJA RAHMAN]

Hello All

I have  added another pvdm 3-16 but still i am not able to configure

video homogeneous

NAME: "CISCO2911/K9 chassis", DESCR: "CISCO2911/K9 chassis"
PID: CISCO2911/K9      , VID: V01 , SN: FCZ143173FC

NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1  , VID: V01 , SN: FOC10501AK8

NAME: "PVDM3 DSP DIMM with 16 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 16 Channels"
PID: PVDM3-16          , VID: V01 , SN: FOC19107FR2

NAME: "PVDM3 DSP DIMM with 16 Channels on Slot 0 SubSlot 5", DESCR: "PVDM3 DSP DIMM with 16 Channels"
PID: PVDM3-16          , VID: V01 , SN: FOC18461QV9

NAME: "C2911 AC Power Supply", DESCR: "C2911 AC Power Supply"
PID: PWR-2911-AC       , VID: V01 , SN: AZS134605NS

dsp 1:
State: UP, firmware: 26.8.0
Max signal/voice channel: 16/16
Max credits: 240
num_of_sig_chnls_allocated: 11
Transcoding channels allocated: 4
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 144, reserved credits: 0
Signaling channels allocated: 4
Voice channels allocated: 0
Credits used (rounded-up): 0
Group: FLEX_GROUP_XCODE, complexity: HIGH
Shared credits: 0, reserved credits: 96
Transcoding channels allocated: 0
Credits used (rounded-up): 0
Slot: 0
Device idx: 0
PVDM Slot: 0
Dsp Type: SP2600

dsp 7:
State: UP, firmware: 26.8.0
Max signal/voice channel: 16/16
Max credits: 240
num_of_sig_chnls_allocated: 0
Transcoding channels allocated: 0
Group: FLEX_GROUP_VOICE, complexity: FLEX
Shared credits: 240, reserved credits: 0
Signaling channels allocated: 0
Voice channels allocated: 0
Credits used (rounded-up): 0
Slot: 0
Device idx: 0

please help

regards

raja

[Rajan]

Hi RR,

Could you also share the "sh run" and " sh inv" for exact calculation. PVDM3-16 should not be enough for configuring video conference even only 4 PRI channels are consumed as per DSP calculator.

HTH

Rajan

[RAJA RAHMAN]

Hello Rajan 

Please find the attached 

and advise shall i mix pvdm 2 and 3 on the same router 

Please advise 

regards

raja 

[aysar3000]

Dear

you cant have video conference with PVDM 3-16

you should have PVDM3-128 or Above