cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
913
Views
16
Helpful
3
Replies

Unable to make calls via new BRI interface

Gordon Ross
Level 9
Level 9

I have a 2901, with a VIC2-2BRI-NT/TE. This is configured via MGCP to a CUCM 8.0.3 system.

I am unable to make or recieve calls on this BRI interface.

Debug isdn q921 shows:

Apr 13 12:42:30: ISDN BR0/0/0 Q921: User TX -> IDREQ ri=41585 ai=127
Apr 13 12:42:32: ISDN BR0/0/0 Q921: User TX -> IDREQ ri=51586 ai=127
Apr 13 12:42:38: ISDN BR0/0/0 Q921: User TX -> IDREQ ri=24995 ai=127

When an inbound call is attempted, I get

Apr 13 12:43:16: ISDN BR0/0/0 Q921: User RX <- SABMEp sapi=0 tei=0
Apr 13 12:43:17: ISDN BR0/0/0 Q921: User RX <- SABMEp sapi=0 tei=0
Apr 13 12:43:18: ISDN BR0/0/0 Q921: User TX -> IDREQ ri=45583 ai=127
Apr 13 12:43:18: ISDN BR0/0/0 Q921: User RX <- SABMEp sapi=0 tei=0
Apr 13 12:43:19: ISDN BR0/0/0 Q921: User RX <- SABMEp sapi=0 tei=0
Apr 13 12:43:20: ISDN BR0/0/0 Q921: User TX -> IDREQ ri=54016 ai=127
Apr 13 12:43:22: ISDN BR0/0/0 Q921: User TX -> IDREQ ri=769 ai=127

but no call.

sh isdn status shows:

dev-gw1#sh isdn sta
Global ISDN Switchtype = basic-net3

%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply

ISDN BRI0/0/0 interface
    dsl 0, interface ISDN Switchtype = basic-net3
    L2 Protocol = Q.921 0x0000  L3 Protocol(s) = CCM MANAGER 0x0003
    Layer 1 Status:
    ACTIVE
    Layer 2 Status:
    Layer 2 NOT Activated
    Layer 3 Status:
    0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask:  0x80000003

From googling, it appears that this is a TEI configuration issue.

In CUCM, my TEI parameters are:

TEI Negotiation: FirstCall

TEI Preservation: Reserve

TEI Mode: Dynamic

I'm in the UK. Are my TEI parameters wrong, or is there something else wrong ?

Thanks,

GTG

Please rate all helpful posts.
1 Accepted Solution

Accepted Solutions

Craig Dyer
Level 3
Level 3

Gordon,

     I cannot remember using to control a BRI in the UK, but I would expect the CuCM to be setup like:-

TEI MODE: Static

TEI: 0

Let me know how you get on,

Craig

View solution in original post

3 Replies 3

Craig Dyer
Level 3
Level 3

Gordon,

     I cannot remember using to control a BRI in the UK, but I would expect the CuCM to be setup like:-

TEI MODE: Static

TEI: 0

Let me know how you get on,

Craig

Doh ! That's it.

Ta,

GTG

Please rate all helpful posts.

Glad to help, thanks for the update.

Have a good day,

Craig

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: