04-05-2023 05:43 AM
Hello,
I am setting up Cisco 840 Wireless phone i was able to get it registered and able to dial out and within. However i have a couple issues i am trying to hash out with these.
I uploaded the sip840-1.8.0.1662-55928.loads file to the tftp file management under the "/" directory and I restarted the TFTP service then in the device defaults I set the 840 in CUCM to sip840-1.8.0.1662-55928.
The phone says that it cannot find that file.
Another issue I am trying to figure out is why this phone when calling out shows just the extension number as called id when calling out? What would cause this I thought the link and partition handles that?
Solved! Go to Solution.
04-06-2023 12:54 AM - edited 04-06-2023 12:56 AM
Maybe because your dialplan is not correct.
If you have a DN in CUCM with just 5552931, you need someting in your whole dialplan in CUCM and / or GW, to add/strip the digits that you need.
From alone, nothing will be done.
And if you think, you have already set it up, then you probably have a problem somewhere. But this is nothing, we (the forum) can provide you an EXACT solution, because nobody else than you knows your whole config, setup, dialplan, ...
So, "trace" a call with DNA in CUCM, check the logs in RTMT, check the logs of your GW/CUBE.
Check the CSS/partition, any potential Router or Translation pattern, calling transformation patterns, ...
This is basic call routing troubleshooting. The steps are always the same.
You should first try to figure it out based on the logs by yourself. And if you have the logs and don't understand them, you can ask in the forum. But not the other way round.
Because it's your job to do basic troubleshooting and take logs and traces. The same steps, if you would ask a TAC. TAC won't take logs for you, so doesn't the community do it.
04-05-2023 09:29 AM - edited 04-05-2023 09:36 AM
I figured out the issue with the firmware. Now I am trying to identify the reason why dialing externally only on the wireless phones it uses just its extension its set up for adding area code/did. For instance if my extension is 5552931 it says its from +1 (555)293-1 on external phone
04-06-2023 12:54 AM - edited 04-06-2023 12:56 AM
Maybe because your dialplan is not correct.
If you have a DN in CUCM with just 5552931, you need someting in your whole dialplan in CUCM and / or GW, to add/strip the digits that you need.
From alone, nothing will be done.
And if you think, you have already set it up, then you probably have a problem somewhere. But this is nothing, we (the forum) can provide you an EXACT solution, because nobody else than you knows your whole config, setup, dialplan, ...
So, "trace" a call with DNA in CUCM, check the logs in RTMT, check the logs of your GW/CUBE.
Check the CSS/partition, any potential Router or Translation pattern, calling transformation patterns, ...
This is basic call routing troubleshooting. The steps are always the same.
You should first try to figure it out based on the logs by yourself. And if you have the logs and don't understand them, you can ask in the forum. But not the other way round.
Because it's your job to do basic troubleshooting and take logs and traces. The same steps, if you would ask a TAC. TAC won't take logs for you, so doesn't the community do it.
04-06-2023 04:56 AM
Thank you was able to figure out with DNA.
04-05-2023 12:11 PM
I recently just got the CP-840 wireless phone. Did you have to go through the hurdles of uploading certificates onto the device to get it working on your network? If so, any tips?
04-06-2023 06:42 AM - edited 04-06-2023 06:44 AM
They're are two different guides on cisco that relatively the same this one however has the certs needed for the device this is what I used had no problem getting the devices registered to UCM:
Certs:
Cisco Manufacturing CA III (cmca3) - Intermediate
Cisco Basic Assurance Root CA 2099 (cbarc2099) - Root for Cisco Manufacturing CA III
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide