Please anyone know why this happened and what I can do to fix?????? Failed to authorize AP Name AP-EYW-GATE with Base Radio MAC Authorization entry does not exist in AAA server.
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.
Forum Posts
Resolved! relocate ISE appliance SNS-3415-K9
Hi all ,we have 4 applinces model SNS-3415-K9 which contain ISE 2.6 in cluster. Each two servers are located in different data cneter.currently we need to move two appliances to new data center. those applience has PAN/MON sec. and PSN.my plan is to ...
Hello. Need some help, please. Cisco ISE PIC does not loading license page after new installation with this error: Error:Unable to load licenseAction.do?command=listWithContainer status:0Version: Ise-pic-3.0.0.458Thank you for yours help.
Hi For ise 3.0 i have tried with multiple users wired/wirless my endpoints are getting the IP address but its not shown on the ISE Logs. Any idea?
Hi ,I am working to get my Cisco ISE send out accounting messages to Fortigate for RSSO (Radius Single Sign On) to work on the Fortigate firewall. I tried adding the Fortigate to the Remote logging targets and added the Fortigate under the Logging ca...
Resolved! Cisco ISE GUI problem (limited version)
Hello.I couldn’t connect to the GUI on my Cisco ISE devices.I followed this URL: https://community.cisco.com/t5/network-access-control/cannot-access-ise-gui/td-p/3220198/page/2I did these steps: ise/admin# application stop ise ise/admin# application...
Hey there, I'm on ISE version 3.0.0.458 and virtual WLC version 8.10.151.0. Here's how my authorization policy and the result is set up: The issue I'm having is I can only reach the Hotspot-Portal on my second attempt connecting to the network. ...
Resolved! ISE Configuration for Netscaler RBAC
Dear Community,I need some assistance with an ISE configuration for Netscaler logins. The Netscaler uses RBAC with command policies such as "superuser", "network" and "sysadmin". I am having a heck of a time trying to figure out how to configure the ...
I have noticed majority of a customers endpoints are showing as "misc" in the endpoints pie chart, see below: What defines this "misc" category and where is this definition configured? If I look at these misc devices, for example some canon printers ...
Hi to all, it seems that ISE has categorized around 70% of our network endpoints as type MISC and 32% out of this MISC type have been categorized as Unknown. In almost all of my switches i do not have dot1.x or MAB, just SNMP, and all of the switch...
Resolved! Pane is dead trying to to a reimages
After having several issues with the Admin node. I reimaged the node. Using the CIMC kvm, I loaded the ISO to map the drive and started the installation process. After about 4 hours I get Pane is dead. I have tried to reboot the server and the cold b...
Hello, An ASR 1002-X with IOS 17.03.03 was acquired.There are few C9300 on the same site with the same IOS version.There are some accounts set in tacacs server with privilege 7 (let say "priv7"). When I used "priv7" and login C9300 by ssh, the privil...
Resolved! ISE report - users last logon time
Hi Folks, I'm really new to ISE and have been trying to find some documentation on how to generate a report on when users last logged on to a network device with their Tacacs account. We have a policy to remove accounts that have been inactive for 6...
Resolved! X-CSRF-TOKEN handling
Hi, Trying to create an endpoint using the API while CSRF Check is enabled; everything works if that check is disabled. Using Python3, sending a GET request first to 'fetch' the token and then feeding that back into the headers for a POST request...
Resolved! Cisco ISE Restore from Backup
I am planning to restore a backup of Cisco ISE to a new VM. The backup is of a VM that is in HA mode. What will happen if I restore a backup from HA setup to a non HA VM? Does it stay as non HA VM?
