Hi ,We apply same config to another switch and it is working.Its gives me below error. Kindly let me know what the error is it is.SW-9200-KP-OOB-UCS(config)# aaa accounting default group PCCU-ISEError: AAA authorization failed AAA_AUTHOR_STATUS_METH...
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community for Help for other best practices.
Forum Posts
Resolved! ISE Self Registered Guest Type
If we choose Self Registered Guest Type with Guest Approval , are we able to assign "Guest Type" profile to registered guest manually During Approval Process ? The idea is every Guest may need different duration of access. Some may 1 day, some may n...
Hi Team,Below are the observations crossed while testing the backupScenario1:Whenever Primary nodes get reboot/failover/Switchover[Promote primary to secondary and Vice versa Secondary node will mark to Primary] - Observed that automatic backup is g...
Resolved! Huawei Switches
Hi all did Huawei Swithces supporting Cisco ISE Profiling configuration ?? BR
Hi Team,Observed the below error at some point, but not able to reproducible.
Hello, I am going to integrate our cisco switches device admin access (TACACS) with Cisco ISE and DUO cloud with the user account located in our on-premises AD. The proposed flow was as follows Switch --> ISE ---> DUO Auth Proxy -->DUO Cloud The plan...
I'm running 3.1.0.518 P8 . I recently registered nodes in a distributed deployment. GUI was working fine, today someone reported that they couldn't get to the GUI. I tried from Chrome, Edge and Firefox no luck. The only change was them being register...
Hi,I'm working on an ISE-implementation and use ISE results for pushing interface templates to the switchports. This to keep the switch/interface configuration at minimum and only have configuration what is needed for the specific devices that will b...
Resolved! ISE / IBNS 2.0 - authentication open
Is anyone doing IBNS 2.0, or is everyone sticking w/ the legacy "authentication" commands that have been available like forever?We're looking into IBNS 2.0 to take advantage of its critical ACL feature that's not available in the legacy auth-manager ...
Hi Guys, I'm installing ISE 1.2 on the network and when testing with few machines, some of them reported "errdisable" status on the port after applying the .1X configuration. The config for the port I have is:switchport access vlan 10switchport mode ...
Hello, everyone!Can someone explain how the switch decides whether to use the primary or secondary PSN when sending Tacacs or Radius authentication requests? It depends on how the switch is configured or something else.Thanks Thanks
how to use smart card authentication for network devices access?i searched SecureCRT and putty CAC can dobut which of these software are the most secure?why most company did not apply these authentication?Some web said using ISE, some use tacacs , wh...
Hello,As part of a project, I need to implement 802.1X within my company. Therefore, I have set up a physical lab consisting of 2 switches and two PCs:- Two Cisco Catalyst 2960 Series switches with Cisco IOS® Software, Release 15.0(2)SE5- PC with Mic...
Hi, on ISE 2.7.0, would it be possible to get a report of the number of active devices on Cisco ISE in the last 30 days?The report should indicate the maximum number of devices seen/authenticated for each day.I tried on the available default reports ...
Dear Community Support.1. I have a need for only a Wired NAC, no wireless or Mobile Device Management. I am trying to understand /clarify what licenses I need to procure.2. I will be deploying two PAN Nodes in a central Data Centre - Primary and Seco...
