tenho um firepower 1140 e tenho internet no firewall vlans e regras simples tambem funcionando mas quando tento por internet nos computadores das vlans simplesmente não funciona. agradeço muito se puderem ajudar .......
Forum Posts
Hi,after a total crash of our FMC 46k HA with v7.4.2 I did a a re-image to v7.4.1.1-12 of both members and restored the backup to the Primary. Everything's well at all, all connected FTDs are there, including the 3110-chassis.Next step rebuilding the...
i have Sophos devices how do i connect to firepower 1120/1150 which type of license do i need to enable RA VPN
Hello everybody, our customer has two FPR 2110 running rel. 6.6.0 managed by FMCv running rel. 6.6.5.2. In the health monitor he see the error message for the FMC: Critical Modules:1,Warning Modules:1,Normal Modules:25,Disabled Modules:15ModuleSmart ...
I need to install a CSPC server in HyperV plataform. From what I checked in the documentation, this is possible, but I did not find any documents with the steps that I must follow with HyperV, I found only with VMWare. Is there a document that can he...
Using OS Code: 9.10(1)27When I do show access-list it gives me output with ACLs having object-groups in source and destination however under that it also list the IPs covered under that object group. I do not want that detailed listing and only the A...
Hi,I have a layer 3 switch (Cisco Catalyst 3560) with multiple vlans configured on it, and connect to switch is inside interface of ASA 5505. Only host in the same vlan with inside interface of firewall can ping it, but I need all vlans can.How would...
Hello everybody,is there an information how long Cisco will still support the unsafe SHA authentication at ASA firewall releaes?Thanks for every hint!ByeR.
Resolved! FTD not receiving SGT inline
Hi,Our FTD 3130 is currently connected to a Catalyst 9407 acting as SDA border node. The link between the Cat9407 and the FTD3130 is a trunk that allows the different VLANs for inter-VN traffic. After running packet captures on the FTD interface I se...
Hi Team,I am looking for the Cisco documentation for a command to check interface optical statistics but I do not see any such documents. Basically, we have deployed Cisco Firepower 4115. It's 2 ports, 1/2 and 1/3 (10G optical) connected to remote en...
is there a current problem with DNS-and-URL-Intelligence-Feed download to FMC ?is there a site in TalosIntelligence.com or other spot, which corroborates 'live status' of these service feeds ? thnxDescription: Cisco-DNS-and-URL-Intelligence-Feed - Do...
Resolved! FTD Backup Cluster mode
Hello,I have 2 FTD on HA and 2 FTDs on Cluster mode, on FMC i am not able to download configuration for FTDs on cluster mode. Is there any way via GUI to perform that or can we just save a running config via cli ? Device mode 4115 version 6.5 , FMC 6...
Hello Everyone,I have recently used cisco firepower 1120 for one of our customer, without any additional licenses. So as per my undertanding all the firepower comes with base license as perpetual. So, I proceed it with basic configuration, which give...
Please I would want to ask for your opinion on the best firewall replacement for ASA 5585-X SSP which is also not end of life any time soon I will be glad if you can share your opinions with me. The most of the task for the firewall will be for IPSEC...
Hi Team:Am having a hard time to understand what went wrong. The site to site was working but I notice the output below: FAB#show crypto ikev2 saIPv4 Crypto IKEv2 SATunnel-id Local Remote fvrf/ivrf Status1 160.238.160.18/500 200.32.190.146/500 none/n...
