Greetings, Can anybody help me know whether cisco firepower management center virtual appliance be deployed on free version of vsphere hypervisor? Thanks
Greetings, Can anybody help me know whether cisco firepower management center virtual appliance be deployed on free version of vsphere hypervisor? Thanks
I have a Cisco ASA 5505. This has been previously configured. I am trying to give it a factory reset and I am being able to connect via Putty and Hyperterminal but I cannot enter anything. I am able to go into ROMMAN mode by using the esc key. Any he...
Can i lock a cisco asa 5585 firewall access list down to use 'service ports' rather than destination ports. The reason i ask for is that we are trying to configure Sharepoint 2013 on our firewall rules for the DMZ. It uses tcp/135 and tcp/53 but it a...
Just curious if I could make any sort of CLI changes on my managed devices w/o using the FMC, and if I did would those changes be synced with the FMC or is it the case that once I set up a device to be managed by the FMC that all my configuration cha...
Hello everyone, I have a problem with my ASA5516, it does not filter the communications via URL FILTERING, in the logs I can see only the default policy (trust all traffic), I have the license URL FILTERING enabled, and the access policy enabled, I d...
Any product available in Cisco to detect data leakage?
Hello, maybe I am not in the right place to ask this questions, but I need some help. So, the deal is, I have certain network, in packet tracer, with 'cloud-PT (Internet)' to router, and servers, connected to 1 switch, then goes 'ASA', and from thi...
Hi guys. I need your help. We have 2 asa, fmc, asdm. Tried to install last software updates (6.2.3), everything went good except one asa. FMC, first ASA updated successfully. But on second asa it doesnt pass readiness check. Currently it's version is...
Hello, I would like to be able to pat a device based on the destination port. For example: 10.10.10.49 (any source any destination) ---- 10.10.10.50 (asa) ----- PAT to ----- 222.222.222.222 But also be able to do this: 10.10.10.49 (any source, desti...
I've created a Geolocation list of countries I want to block. Do I put it in my Access Control list as the destination network, source network, or both? If I put the geo list in both, does the FMC interpret it as an AND operator? Meaning the tra...
Hi Guys, Just need your assistance on this. I'm trying to setup a GNS3 lab. Attached is the diagram. For some reason, I'm cannot ping the devices behind the firewall. Here are the FW config. FW1# sh run natnat (INSIDE,WAN0) source dynamic any ...
Hi, I have an ASA5508-X running FTD 6.2.2-81 which has just gone into production, but I'd like to add an FMC virtual appliance to the environment to control the firewall. When I register the FTD to the FMC, will the on-box configuration be imported...
would it possible to configure the management interface on the 5555-x with an IP address and also set the interface IP as the default gateway of the Firepower? I am out of available interface on the 5555-x, some cisco doc says its possible, but I w...
Hi Recently we had issue in Microsoft Office communicator, users were not able to share their desktops however the ports are enabled. A microsoft has said that this Cipher suit is normally blocked in firewall and we have to enable ...
I need to replace the primary 5516 ASA but am confused when it comes to getting the configuration written over to it. I configured the failover interface but I am wondering how to get all configurations written from the secondary (which would be the ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
10 | |
8 | |
5 | |
4 | |
1 |