Good afternoon, I have a cisco asa5500 that working in Active/Standby mode with: Cisco Adaptive Security Appliance Software Version 7.1(2)Device Manager Version 5.1(2) Hardware: ASA5550, 3968 MB RAM, CPU Pentium 4 3000 MHzInternal ATA Compact Fla...
Forum Posts
Hi Can any one help me to implement Below scenario : I am having ASA 5508X box with firepower, I have connected interface Gi1/1 to MGMT PC for ASDM access interface Gi1/4 with interface MGMT1/1 for Firepower connectivity and interface Gi1/1 and Gi1/4...
I would think this would be reasonably easy, but could not find the simple explanation for how to accomplish getting an ASA 5506-x w/Firepower running and licensed, specifically how it works (or if it needs to) with Cisco Firepower Management Center....
I want two interfaces to be bridged, where the scenario is i have connected management interface to gigabit1/4 and bridging applies between gigabit1/1 and gigabit1/4..so that i only get one uplink for both ASDM and firepower. Is it possible to do...
Hi Can any one help me to implement Below scenario : I am having ASA 5508X box with firepower, I have connected interface Gi1/1 to MGMT PC for ASDM access interface Gi1/4 with interface MGMT1/1 for Firepower connectivity and interface Gi1/1 and Gi1/4...
Resolved! ASA 5520 Issue
I have an ASA 5520 and it's show me this error "mount: mounting /dev/hda1 on /mnt/disk0 failed: No such device or address"How I can fix it? Can you give me a procedure?
Hi I just completed the training for the CCENT ICDN1 coarse before I start ICDN2 coarse. I wanted to do the Labs for the coarse and I have lost the URL for the Labs. Got my login details but can`t find the URL. Does anyone know the URL that I nee...
After Upgrading from one ASA 5505 to another with a newer build I can no longer connect to the internet. Anyone have any suggestions? Below is attached config: : Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz!ASA Version 9.2(4)!hostname ASA-5...
Resolved! NAT Translated objects
ASA 5555, IOS 9.2 using ASDM 7.2 Totally new to this newer way of doing NAT since the 8.4(?) changes. So when creating a static NAT you need to create all new translated services? There are no defaults.Lets say that I have a server on the inside that...
I have setup remote access VPN on 6.2.3. I am able to connect from any device but I am unable to access any internal network. I have the NAT exemptions and networks allowed in the access policy. But the FTD does not redistribute the static route f...
Resolved! Cisco ASA 5505 nat
I'm running into an issue where we have an older Cisco ASA 5505. Needless to say, it's quite old and we want to replace it with a newer Cisco ASA 5585. This ASA has been on the shelf for a couple of years so I'm pretty rusty with the Cisco stuff an...
Hi guys, I cannot have access without Identity NAT configured. Object: LAN object network LAN subnet 10.100.52.0 255.255.255.0 NAT: object network LAN nat (inside,outside) static 10.100.52.0 no-proxy-arp route-lookup I want to emphasise tha...
Hi, Recently we migrated our FireSIGHT and firePOWER modules to v6 which has progressed smoothly although i am having issues updating the firepower modules for a remote site with low bandwidth from the fireSIGHT interface to 6.1.0.2-57. All the other...
Hello I have a Cisco Firewall FirePower 5506 and suddenly its consuming high memory it was on 3% and now its on 83% . I have disabled all the Syslogs and logging on this firewall however no change at all memory is still very high . Please guide ...
Hi; I installed FTDv 6.2.2 on ESXi and want to register it on FMC. But while I SSH to the FTDv, I always put in expert mode (admin@firepower:~$). I tried "exit" and "logout" command and even "CTRL+A then D" keys but all of them just logout me from ...
